P0335 2006 Nissan Altima Sedan Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2006 Nissan Altima Sedan indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2006 Nissan Altima Sedan Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2006 Nissan Altima Sedan?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2006 Nissan Altima Sedan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2006 Nissan Altima Sedan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2006 Nissan Altima Sedan code?
Need more information on how to fix the P0335 2006 Nissan Altima Sedan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2006 Nissan Altima Sedan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2006 Nissan Altima Sedan Code
1. What does the OBDII code P0335 mean on a 2006 Nissan Altima?
P0335 indicates a malfunction in the crankshaft position sensor circuit, which means the Engine Control Module (ECM) is not receiving the correct signal from the sensor.
2. What are the symptoms of a P0335 code in a 2006 Nissan Altima?
Symptoms may include difficulty starting the engine, stalling, poor acceleration, reduced fuel efficiency, or the engine not starting at all.
3. What causes the P0335 code in a 2006 Nissan Altima?
Common causes include a faulty crankshaft position sensor, damaged wiring or connectors in the sensor circuit, a failed ECM, or issues with the sensor's reluctor ring.
4. How do you diagnose the P0335 code on a 2006 Nissan Altima?
Diagnosis typically involves using an OBDII scanner to confirm the code, visually inspecting the sensor and wiring, testing the sensor with a multimeter, and checking for proper alignment of the reluctor ring.
5. Can I drive my 2006 Nissan Altima with a P0335 code?
It’s not recommended, as the engine may stall or fail to start, potentially leaving you stranded or causing unsafe driving conditions.
6. How do you fix the P0335 code on a 2006 Nissan Altima?
Repairs may include replacing the crankshaft position sensor, repairing or replacing damaged wiring or connectors, or addressing issues with the reluctor ring or ECM.
7. Where is the crankshaft position sensor located on a 2006 Nissan Altima?
The crankshaft position sensor is typically located near the bottom of the engine, close to the crankshaft pulley or flywheel.
8. How much does it cost to fix a P0335 code on a 2006 Nissan Altima?
Replacing the crankshaft position sensor typically costs between $100 and $300, including parts and labor. Wiring or ECM repairs may increase the cost.
9. What happens if the P0335 code is ignored on a 2006 Nissan Altima?
Ignoring this code can lead to worsening performance issues, engine stalling, or permanent damage to other engine components.
10. Can a dead battery cause the P0335 code on a 2006 Nissan Altima?
While unlikely, a weak or dead battery can sometimes cause electrical issues, including false sensor readings. It’s worth checking the battery and charging system during diagnosis.
Discuss the causes and fixes for P0335 2006 Nissan Altima Sedan OBDII Code
Code P0335 2006 Nissan Altima Sedan comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
