P0335 2003 Nissan Altima Sedan Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2003 Nissan Altima Sedan indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2003 Nissan Altima Sedan Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2003 Nissan Altima Sedan?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2003 Nissan Altima Sedan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2003 Nissan Altima Sedan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2003 Nissan Altima Sedan code?
Need more information on how to fix the P0335 2003 Nissan Altima Sedan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2003 Nissan Altima Sedan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2003 Nissan Altima Sedan Code
1. What are the common symptoms of OBDII code P0335 in a 2003 Nissan Altima Sedan?
- Common symptoms include engine misfires, rough idling, stalling, poor acceleration, and difficulty starting the vehicle.
2. What does OBDII code P0335 indicate in a 2003 Nissan Altima Sedan?
- OBDII code P0335 signifies a problem with the crankshaft position sensor circuit in the vehicle.
3. What are the possible causes of OBDII code P0335 in a 2003 Nissan Altima Sedan?
- The possible causes include a faulty crankshaft position sensor, damaged wiring or connectors related to the sensor, or an issue with the sensor's alignment.
4. How can I diagnose the issue related to OBDII code P0335 in my 2003 Nissan Altima Sedan?
- A diagnostic scan tool can help you read the code and identify the specific problem. Additionally, checking the sensor's wiring and connections for any damage or loose connections can be helpful.
5. Can I drive my 2003 Nissan Altima Sedan with OBDII code P0335?
- It is not recommended to drive the vehicle with this code present, as it can lead to further engine damage or potential safety hazards due to erratic engine behavior.
6. Is it possible to repair OBDII code P0335 in a 2003 Nissan Altima Sedan on my own?
- Depending on your level of automotive expertise, you may be able to replace the crankshaft position sensor or repair any damaged wiring yourself. However, seeking professional help is advisable for accurate diagnosis and repair.
7. How much does it typically cost to repair OBDII code P0335 in a 2003 Nissan Altima Sedan?
- The cost of repair can vary depending on the extent of the issue and whether you choose to do it yourself or seek professional help. Generally, replacing the crankshaft position sensor can range from $100 to $300, including parts and labor.
8. Are there any preventive measures I can take to avoid OBDII code P0335 in my 2003 Nissan Altima Sedan?
- Regularly scheduled maintenance, such as checking and replacing the crankshaft position sensor at recommended intervals, can help prevent issues that may trigger OBDII code P0335.
9. Will resetting the OBDII code P0335 in my 2003 Nissan Altima Sedan make it go away permanently?
- Resetting the code may temporarily clear the warning light, but if the underlying issue causing OBDII code P0335 is not addressed, the code is likely to reappear.
10. Can a faulty crankshaft position sensor cause other problems in a 2003 Nissan Altima Sedan besides triggering OBDII code P0335?
- Yes, a faulty crankshaft position sensor can lead to other issues like poor fuel economy, engine misfires, and difficulty shifting gears in an automatic transmission vehicle.
Discuss the causes and fixes for P0335 2003 Nissan Altima Sedan OBDII Code
-
i got a problem with my 2003 Altima 2.5l p0335 battery voltage is good and starter is good
-
If the starter and battery voltage is OK, then you have to replace the crankshaft position sensor to fix the problem.
-
I av nissan altima 2003 the car is starting fine but throttle is not raising well
-
If you have the P0335 code, then you should start by replacing the Crankshaft Position Sensor
-
yep 03 altima 2.5l got the po335 and the po725 showup, replaced the crank pos sensor but the car is still running poorly, any ideas? runs so poorly now i dont even wanna dry it to the shop to get a new diagnostic read
-
When you say "Car is Running Poorly" do you mean that the engine is running rough or is not shifting?
Was the engine running poorly before you replace the Crankshaft Position Sensor?
Do you have any more codes? -
engine is running rough yes, i did a small test drive after i put the sensor in ran great turned the vehicle off. Got back in within 5mins to run to town for the real test and grab lunch, started bucking again and just ran poorly so i parked her again
-
Is it advised to replace the camshaft sensor as well as this is something i did not do
-
Usually bad Crankshaft Position Sensor and the Camshaft Position Sensor will not cause the engine to run rough, will cause the engine to stall or a hard start, but no rough idle.
Do you have any other codes? -
No other codes, just went ahead and replaced the camshaft sensor just to get the pair done, thinking about pulling the back seats out to check the quality of the gas due to this problem showing up after ive gotten gas, pull the sparkplugs and check them as well.
-
The sensor is between the transmission and the upper oil pan, you have to access the sensor from underneath the vehicle. This is the only image I got.
Click here to enlarge image
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
