P0335 1997 Toyota Camry Code - Crankshaft Position Sensor 'A' Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 1997 Toyota Camry indicates Crankshaft Position Sensor 'A' Circuit .
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 1997 Toyota Camry Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 1997 Toyota Camry?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 1997 Toyota Camry?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 1997 Toyota Camry code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 1997 Toyota Camry code?
Need more information on how to fix the P0335 1997 Toyota Camry code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 1997 Toyota Camry code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 1997 Toyota Camry Code
1. What are the common symptoms of OBDII code P0335 in a 1997 Toyota Camry?
- Common symptoms include engine stalling, rough idling, difficulty starting the vehicle, and a decrease in fuel efficiency.
2. What does the OBDII code P0335 for a 1997 Toyota Camry indicate?
- This code indicates a problem with the crankshaft position sensor 'A' circuit. The sensor helps the engine control module (ECM) determine the position of the crankshaft for proper ignition timing.
3. What are the possible causes of OBDII code P0335 in a 1997 Toyota Camry?
- The possible causes include a faulty crankshaft position sensor, damaged wiring or connectors related to the sensor, or issues with the ECM itself.
4. How can I diagnose the issue causing OBDII code P0335 in my 1997 Toyota Camry?
- You can use a multimeter to test the crankshaft position sensor for proper resistance and voltage output. Additionally, check the wiring and connectors for any visible damage.
5. Can I continue to drive my 1997 Toyota Camry with OBDII code P0335?
- It's not recommended to drive the vehicle with this code present, as it can lead to further engine damage or potential safety hazards. It's best to address the issue promptly.
6. How can I repair OBDII code P0335 in my 1997 Toyota Camry?
- The most common repair involves replacing the faulty crankshaft position sensor. Ensure proper installation and check the wiring for any issues before clearing the code.
7. Is it necessary to reset the ECM after repairing OBDII code P0335 in a 1997 Toyota Camry?
- Yes, it's important to reset the ECM to clear the error code after addressing the underlying issue. This can be done using an OBDII scanner or by disconnecting the car battery for a few minutes.
8. Can a DIY enthusiast fix OBDII code P0335 in a 1997 Toyota Camry?
- Depending on your experience and tools available, replacing the crankshaft position sensor can be a DIY-friendly repair. However, if you're unsure, it's best to consult a professional mechanic.
9. How much does it cost to repair OBDII code P0335 in a 1997 Toyota Camry at a mechanic's shop?
- The cost can vary depending on the labor rates and parts prices in your area. On average, expect to pay between $150 to $300 for parts and labor to replace the crankshaft position sensor.
10. Will fixing OBDII code P0335 improve the performance of my 1997 Toyota Camry?
- Yes, addressing this code can restore proper engine performance, improve fuel efficiency, and eliminate the symptoms associated with a faulty crankshaft position sensor.
Discuss the causes and fixes for P0335 1997 Toyota Camry OBDII Code
Code P0335 1997 Toyota Camry comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
