P0304 2007 Ford Fusion Code - Cylinder 4 Misfire Detected
Quick Answer
Misfire is defined as a lack of combustion in a cylinder due to the absence of a spark, incorrect fuel metering, low compression, or any other cause. Common causes include Faulty Spark Plug #4, Clogged or faulty Fuel Injector #4, Faulty Ignition Coil #4. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0304 2007 Ford Fusion indicates Cylinder 4 Misfire Detected.
- Common causes
- Common causes include Faulty Spark Plug #4, Clogged or faulty Fuel Injector #4, Faulty Ignition Coil #4.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0304 2007 Ford Fusion Description
When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the Crankshaft Position (CKP) sensor signal to vary, the Engine Control Module (ECM) can determine that a misfire is occurring.
The Malfunction Indicator Lamp (MIL) blinks once per second when detecting a misfire severe enough to cause catalyst damage. If the MIL is in a steady state due to a misfire, this indicates the threshold for emissions was exceeded and caused the vehicle to fail an inspection and maintenance tailpipe test.
This Diagnostic Trouble Code (DTC) sets when the misfire detection monitor detects an engine misfire in cylinder 4.
What are the Possible Causes of the DTC P0304 2007 Ford Fusion?
- Faulty Spark Plug #4
- Clogged or faulty Fuel Injector #4
- Faulty Ignition Coil #4
- Fuel Injector #4 harness is open or shorted
- Fuel Injector #4 circuit poor electrical connection
- Ignition Coil #4 harness is open or shorted
- Ignition Coil #4 circuit poor electrical connection
- Insufficient cylinder 4 compression
- Incorrect fuel pressure
- Intake air leak
How to Fix the DTC P0304 2007 Ford Fusion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0304 2007 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0304 2007 Ford Fusion code?
Need more information on how to fix the P0304 2007 Ford Fusion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0304 2007 Ford Fusion code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0304 2007 Ford Fusion Code
1. What are the common symptoms of OBDII code P0304 (Cylinder 4 Misfire Detected) in a 2007 Ford Fusion?
- Common symptoms include engine misfiring, rough idling, loss of power, and potential decrease in fuel efficiency.
2. What are the possible causes of a Cylinder 4 misfire in a 2007 Ford Fusion triggering code P0304?
- Common causes may include faulty spark plugs, ignition coils, fuel injectors, vacuum leaks, low compression, or issues with the engine control module.
3. How can I diagnose the specific cause of the Cylinder 4 misfire in my 2007 Ford Fusion?
- Diagnosis typically involves checking spark plugs, ignition coils, fuel injectors, compression levels, vacuum lines, and conducting a thorough inspection of the ignition system.
4. Can a dirty or clogged fuel injector cause a Cylinder 4 misfire in a 2007 Ford Fusion?
- Yes, a dirty or clogged fuel injector can disrupt the fuel delivery to Cylinder 4, leading to a misfire and triggering OBDII code P0304.
5. Is it safe to continue driving my 2007 Ford Fusion with OBDII code P0304 (Cylinder 4 Misfire Detected) present?
- It is not recommended to drive the vehicle with a misfire as it can cause further damage to the engine and emission control system. Immediate diagnosis and repair are advised.
6. How can I repair a Cylinder 4 misfire in my 2007 Ford Fusion to clear OBDII code P0304?
- Repair may involve replacing spark plugs, ignition coils, fuel injectors, addressing vacuum leaks, checking compression, or repairing issues with the engine control module.
7. Can a bad ignition coil be the sole reason for a Cylinder 4 misfire in a 2007 Ford Fusion?
- Yes, a faulty ignition coil can cause a misfire in Cylinder 4, leading to the triggering of OBDII code P0304.
8. Will resetting the OBDII code P0304 in my 2007 Ford Fusion make the misfire issue disappear?
- Resetting the code may temporarily clear the warning light, but the underlying issue causing the Cylinder 4 misfire needs to be diagnosed and repaired to prevent future occurrences.
9. How important is it to address OBDII code P0304 (Cylinder 4 Misfire Detected) promptly in a 2007 Ford Fusion?
- It is crucial to address the misfire issue promptly to prevent further damage to the engine components, ensure optimal performance, and maintain fuel efficiency.
10. Can a simple tune-up resolve the Cylinder 4 misfire issue causing OBDII code P0304 in a 2007 Ford Fusion?
- A tune-up, including replacing spark plugs, can sometimes resolve a misfire issue, but if the problem persists, a more in-depth diagnosis may be necessary to identify the root cause.
Discuss the causes and fixes for P0304 2007 Ford Fusion OBDII Code
Code P0304 2007 Ford Fusion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
