P0222 2008 Toyota Prius Code - Throttle/Pedal Position Sensor/Switch 'B' Circuit - Low Input
Quick Answer
Electric Throttle Control Actuator consists of throttle control motor, throttle position sensor (TPS), etc. Common causes include Faulty Throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0222 2008 Toyota Prius indicates Throttle/Pedal Position Sensor/Switch 'B' Circuit - Low Input.
- Common causes
- Common causes include Faulty Throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0222 2008 Toyota Prius Description
The throttle position sensor has the two sensors. These sensors are a kind of potentiometers which transform the throttle valve position into output voltage, and emit the voltage signal to the Engine Control Module (ECM) In addition, these sensors detect the opening and closing speed of the throttle valve and feed the voltage signals to the ECM. The ECM judges the current opening angle of the throttle valve from these signals and the ECM controls the throttle control motor to make the throttle valve opening angle properly in response to driving condition.
What are the Possible Causes of the DTC P0222 2008 Toyota Prius?
- Faulty Throttle position sensor
- Throttle position sensor harness is open or shorted
- Throttle position sensor poor electrical connection
How to Fix the DTC P0222 2008 Toyota Prius?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0222 2008 Toyota Prius code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0222 2008 Toyota Prius code?
Need more information on how to fix the P0222 2008 Toyota Prius code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0222 2008 Toyota Prius code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0222 2008 Toyota Prius Code
1. What are the common symptoms of OBDII code P0222 in a 2008 Toyota Prius?
The common symptoms of code P0222 include reduced engine power, hesitation or stalling during acceleration, and the vehicle going into limp mode.
2. What does the Throttle/Pedal Position Sensor/Switch 'B' Circuit - Low Input mean in a 2008 Toyota Prius?
The code P0222 indicates that the Engine Control Module (ECM) has detected a low voltage input from the throttle/pedal position sensor or switch 'B'.
3. What are the possible causes of OBDII code P0222 in a 2008 Toyota Prius?
Possible causes of code P0222 include a faulty throttle position sensor, damaged wiring or connectors in the sensor circuit, or issues with the ECM itself.
4. How can I diagnose the Throttle/Pedal Position Sensor/Switch 'B' Circuit issue in my 2008 Toyota Prius?
Diagnosing code P0222 involves using a scan tool to check for the code, inspecting the throttle position sensor and its wiring, and performing voltage tests to determine the cause of the low input signal.
5. Can I continue driving my 2008 Toyota Prius with OBDII code P0222?
It is not recommended to continue driving with code P0222 as it can lead to further engine performance issues and potential safety hazards. It's best to address the problem promptly.
6. How can I repair OBDII code P0222 in my 2008 Toyota Prius?
Repairing code P0222 may involve replacing the throttle position sensor, repairing any damaged wiring or connectors, or reprogramming the ECM if necessary.
7. Is it possible to reset OBDII code P0222 in a 2008 Toyota Prius without repairing the issue?
While you can clear the code with a scan tool, it will likely reappear if the underlying problem is not addressed. It's important to fix the root cause of the code.
8. How much does it typically cost to fix OBDII code P0222 in a 2008 Toyota Prius?
The cost of fixing code P0222 can vary depending on the exact cause of the issue. Replacing the throttle position sensor or repairing wiring may cost a few hundred dollars, including parts and labor.
9. Will OBDII code P0222 cause my 2008 Toyota Prius to fail an emissions test?
Yes, code P0222 can cause your vehicle to fail an emissions test as it indicates a problem with the throttle position sensor circuit, which can affect engine performance and emissions.
10. How can I prevent OBDII code P0222 from occurring in my 2008 Toyota Prius in the future?
To prevent code P0222, it's essential to perform regular maintenance on your vehicle, including checking the throttle position sensor and its wiring for any signs of wear or damage.
Discuss the causes and fixes for P0222 2008 Toyota Prius OBDII Code
Code P0222 2008 Toyota Prius comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
