P0193 2012 Ford Fusion Code - Fuel Rail Pressure Sensor Circuit High Input
Quick Answer
The FRP sensor is a diaphragm strain gauge device. Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0193 2012 Ford Fusion indicates Fuel Rail Pressure Sensor Circuit High Input.
- Common causes
- Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0193 2012 Ford Fusion Description
The FRP sensor is located on the fuel rail, and provides a feedback signal to indicate the fuel rail pressure to the Powertrain Control Module (PCM). The PCM uses the FRP signal to command the correct injector timing and pulse width for correct fuel delivery at all speed and load conditions. The FRP sensor, along with the fuel volume regulator (part of the fuel injection pump), form a closed loop fuel pressure control system. An electrically faulted FRP sensor results in the deactivation of the fuel injection pump. Fuel pressure to injectors is then provided only by the FP module. When the fuel injection pump is de-energized and the injectors are active, the fuel rail pressure is approximately 70 kPa (10 psi) lower than FP module pressure due to the pressure drop across the fuel injection pump. Thus, if the FP module pressure is 448 kPa (65 psi), then the fuel rail pressure would be approximately 379 kPa (55 psi) if the injectors are active.
What are the Possible Causes of the DTC P0193 2012 Ford Fusion?
- Low or no fuel
- Faulty Rail Pressure (FRP) Sensor
- FRP harness is open or shorted
- FRP circuit poor electrical connection
- Faulty Fuel Pump
How to Fix the DTC P0193 2012 Ford Fusion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0193 2012 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0193 2012 Ford Fusion code?
Need more information on how to fix the P0193 2012 Ford Fusion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0193 2012 Ford Fusion code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0193 2012 Ford Fusion Code
1. What are the common symptoms of OBDII code P0193 on a 2012 Ford Fusion?
- Common symptoms include rough idling, loss of power, engine stalling, and the illumination of the check engine light.
2. What does the OBDII code P0193 Fuel Rail Pressure Sensor Circuit High Input mean on a 2012 Ford Fusion?
- This code indicates that the fuel rail pressure sensor is detecting a higher than expected voltage input, typically due to a malfunction in the sensor or its circuit.
3. What are the possible causes of OBDII code P0193 on a 2012 Ford Fusion?
- Potential causes include a faulty fuel rail pressure sensor, damaged wiring or connectors in the sensor circuit, issues with the fuel pump, or a problem with the vehicle's fuel system.
4. How can I diagnose the OBDII code P0193 on my 2012 Ford Fusion?
- Diagnosis typically involves checking the fuel rail pressure sensor and its wiring for any visible damage, testing the sensor's voltage output, and verifying the fuel pressure readings with a diagnostic tool.
5. Can I still drive my 2012 Ford Fusion with OBDII code P0193 Fuel Rail Pressure Sensor Circuit High Input?
- It is not recommended to drive the vehicle with this code active, as it can lead to engine performance issues and potential damage to other components in the fuel system.
6. How do I repair OBDII code P0193 on a 2012 Ford Fusion?
- Repair may involve replacing the fuel rail pressure sensor, repairing or replacing damaged wiring or connectors, addressing issues with the fuel pump, or resetting the fault code after fixing the underlying problem.
7. Will resetting the OBDII code P0193 on my 2012 Ford Fusion make it go away permanently?
- Simply resetting the code without addressing the root cause will not resolve the issue permanently, as the check engine light is likely to come back on once the problem is detected again.
8. Is it possible to prevent OBDII code P0193 from occurring on my 2012 Ford Fusion?
- Regular maintenance of the fuel system, including checking for leaks, ensuring proper fuel quality, and timely replacement of fuel system components, can help prevent issues leading to this code.
9. Can a DIY enthusiast fix OBDII code P0193 on a 2012 Ford Fusion?
- While some skilled DIYers may be able to diagnose and replace the fuel rail pressure sensor or address wiring issues, it is recommended to consult a professional mechanic for proper diagnosis and repair.
10. How much does it cost to repair OBDII code P0193 on a 2012 Ford Fusion?
- The cost of repairs can vary depending on the exact cause of the code, but it may involve a sensor replacement, wiring repairs, or fuel system maintenance, with total costs ranging from $100 to $500 or more.
Discuss the causes and fixes for P0193 2012 Ford Fusion OBDII Code
Code P0193 2012 Ford Fusion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
