AutoCodes – Ford – P0192 2002 Ford F150

P0192 2002 Ford F150 Code - Fuel Rail Pressure Sensor Circuit Low Input

Quick Answer

The FRP sensor is a diaphragm strain gauge device. Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P0192 2002 Ford F150 indicates Fuel Rail Pressure Sensor Circuit Low Input.
Common causes: Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 2,676

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 30, 2022

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0192 2002 Ford F150 Description

The FRP sensor is a diaphragm strain gauge device. The FRP sensor measures the pressure difference between the fuel rail and atmospheric pressure. The FRP sensor nominal output varies between 0.5 and 4.5 volts, with 0.5 volts corresponding to 0 MPa (0 psi) gauge and 4.5 volts corresponding to 26 MPa (3771 psi) gauge. The sensor can read vacuums and may lower the output voltage to slightly below 0.5 volts. This condition is normal and is usually the case after several hours of cold soak before the vehicle dome light is turned on. The FP module is energized at the same time the dome light is commanded on. A disabled or malfunctioning dome light does not affect the FP module control.
The FRP sensor is located on the fuel rail, and provides a feedback signal to indicate the fuel rail pressure to the Powertrain Control Module (PCM). The PCM uses the FRP signal to command the correct injector timing and pulse width for correct fuel delivery at all speed and load conditions. The FRP sensor, along with the fuel volume regulator (part of the fuel injection pump), form a closed loop fuel pressure control system. An electrically faulted FRP sensor results in the deactivation of the fuel injection pump. Fuel pressure to injectors is then provided only by the FP module. When the fuel injection pump is de-energized and the injectors are active, the fuel rail pressure is approximately 70 kPa (10 psi) lower than FP module pressure due to the pressure drop across the fuel injection pump. Thus, if the FP module pressure is 448 kPa (65 psi), then the fuel rail pressure would be approximately 379 kPa (55 psi) if the injectors are active.

OBDII Code P0192 2002 Ford F150 - Fuel Rail Pressure Sensor Circuit Low Input - AutoCodes.com — P0192 2002 Ford F150 Code - Fuel Rail Pressure Sensor Circuit Low Input

What does this mean?

What are the Possible Causes of the DTC P0192 2002 Ford F150?

Low or no fuel
Faulty Rail Pressure (FRP) Sensor
FRP harness is open or shorted
FRP circuit poor electrical connection
Faulty Fuel Pump

How to Fix the DTC P0192 2002 Ford F150?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

The comprehensive component monitor (CCM) monitors the FRP sensor circuit to the PCM for low voltage. If voltage were to fall below a calibrated limit and amount of time during testing, the test will fail.
A FRP PID value during KOER or KOEO less than 0.3 volts for gasoline or 0.5 volts for natural gas vehicles (NG) would indicate a hard fault.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0192 2002 Ford F150 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0192 2002 Ford F150 code?

Need more information on how to fix the P0192 2002 Ford F150 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0192 2002 Ford F150 code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0192 2002 Ford F150 Code

1. What are the common symptoms of OBDII code P0192 on a 2002 Ford F150?

- Common symptoms include rough idling, engine misfires, decreased fuel efficiency, and potential stalling.

2. What does the OBDII code P0192 for a 2002 Ford F150 indicate?

- The code indicates a low input signal from the fuel rail pressure sensor circuit.

3. What are the possible causes of the P0192 code on a 2002 Ford F150?

- Possible causes include a faulty fuel rail pressure sensor, wiring issues, a clogged fuel filter, or a problem with the fuel pump.

4. How can I diagnose the P0192 code on my 2002 Ford F150?

- Diagnose the code by checking the fuel rail pressure sensor for proper operation, inspecting the wiring for any damage, and testing the fuel pressure using a gauge.

5. Can I continue driving my 2002 Ford F150 with the P0192 code?

- It is not recommended to continue driving with the P0192 code as it can lead to poor engine performance and potential damage.

6. How can I repair the P0192 code on a 2002 Ford F150?

- Repair options include replacing the fuel rail pressure sensor, repairing any damaged wiring, replacing the fuel filter, or addressing any fuel pump issues.

7. Will resetting the OBDII code P0192 on a 2002 Ford F150 make it go away permanently?

- Resetting the code may temporarily clear it, but if the underlying issue is not addressed, the code is likely to reappear.

8. Are there any preventive maintenance tips to avoid the P0192 code on a 2002 Ford F150?

- Regularly checking and replacing the fuel filter, ensuring proper fuel system maintenance, and using high-quality fuel can help prevent the P0192 code.

9. How long does it typically take to repair the P0192 code on a 2002 Ford F150?

- The repair time can vary depending on the exact cause of the code, but it may take anywhere from 1 to 3 hours to diagnose and fix the issue.

10. Can a DIY enthusiast fix the P0192 code on a 2002 Ford F150?

- Depending on the individual's skill level and access to tools, a DIY enthusiast may be able to address the P0192 code by following repair guides and using the necessary equipment.