P0122 2013 Nissan Rogue Code - Throttle Position Sensor/Switch '1' Circuit Low Input
Quick Answer
The Throttle Pedal Position (TPP) responds to the accelerator pedal movement. Common causes include Faulty throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0122 2013 Nissan Rogue indicates Throttle Position Sensor/Switch '1' Circuit Low Input.
- Common causes
- Common causes include Faulty throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0122 2013 Nissan Rogue Description
Idle position of the throttle valve is determined by the ECM receiving the signal from the throttle position sensor. This sensor controls engine operation such as fuel cut. On the other hand, the Wide open and closed throttle position switch, which is built into the throttle position sensor unit, is not used for engine control.
What are the Possible Causes of the DTC P0122 2013 Nissan Rogue?
- Faulty throttle position sensor
- Throttle position sensor harness is open or shorted
- Throttle position sensor circuit poor electrical connection
- Faulty accelerator pedal position sensor
How to Fix the DTC P0122 2013 Nissan Rogue?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0122 2013 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0122 2013 Nissan Rogue code?
Need more information on how to fix the P0122 2013 Nissan Rogue code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0122 2013 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0122 2013 Nissan Rogue Code
1. What are the common symptoms of OBDII code P0122 in a 2013 Nissan Rogue?
- Common symptoms include decreased engine performance, poor acceleration, stalling, and in some cases, the vehicle may go into limp mode.
2. What does the OBDII code P0122 on a 2013 Nissan Rogue indicate?
- The code P0122 indicates a low input signal from the throttle position sensor or switch '1' circuit in the vehicle.
3. What are the possible causes of OBDII code P0122 in a 2013 Nissan Rogue?
- Possible causes include a faulty throttle position sensor, damaged wiring or connectors in the circuit, or issues with the engine control module (ECM).
4. How can I diagnose the cause of OBDII code P0122 in my 2013 Nissan Rogue?
- To diagnose the issue, you can use a scan tool to check for the specific voltage readings from the throttle position sensor and inspect the wiring and connectors for any damage.
5. Can I drive my 2013 Nissan Rogue with the OBDII code P0122?
- It is not recommended to drive the vehicle with code P0122 as it can lead to reduced engine performance and potential safety hazards. It is best to address the issue promptly.
6. How can I repair OBDII code P0122 on a 2013 Nissan Rogue?
- Repair options may include replacing the throttle position sensor, repairing any damaged wiring or connectors, or resetting the ECM after fixing the issue.
7. Will resetting the OBDII code P0122 on my 2013 Nissan Rogue make it go away permanently?
- Resetting the code may temporarily clear the warning, but if the underlying issue causing the code is not fixed, it is likely to reappear after some driving cycles.
8. How much does it typically cost to repair OBDII code P0122 in a 2013 Nissan Rogue?
- The cost of repair can vary depending on the exact cause of the issue, but it may range from $100 to $300 for parts and labor.
9. Can a DIY enthusiast fix OBDII code P0122 in a 2013 Nissan Rogue?
- Depending on your skill level and access to tools, some DIY enthusiasts may be able to address the issue by replacing the throttle position sensor or repairing wiring themselves.
10. Is it necessary to visit a dealership for repairing OBDII code P0122 in a 2013 Nissan Rogue?
- While visiting a dealership is an option, independent mechanics or DIY repairs can also successfully address the OBDII code P0122 in a 2013 Nissan Rogue.
Discuss the causes and fixes for P0122 2013 Nissan Rogue OBDII Code
Code P0122 2013 Nissan Rogue comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
