P0122 2003 Jeep Liberty Code - Throttle Position Sensor/Accelerator Position Pedal Circuit Low Input
Quick Answer
The Throttle Position Sensor (TPS) responds to the accelerator pedal movement. Common causes include Faulty throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0122 2003 Jeep Liberty indicates Throttle Position Sensor/Accelerator Position Pedal Circuit Low Input.
- Common causes
- Common causes include Faulty throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0122 2003 Jeep Liberty Description
Idle position of the throttle valve is determined by the PCM receiving the signal from the throttle position sensor. This sensor controls engine operation such as fuel cut. On the other hand, the Wide open and closed throttle position switch, which is built into the throttle position sensor unit, is not used for engine control.
What are the Possible Causes of the DTC P0122 2003 Jeep Liberty?
- Faulty throttle position sensor
- Throttle position sensor harness is open or shorted
- Throttle position sensor circuit poor electrical connection
- Faulty Powertrain Control Module (PCM)
How to Fix the DTC P0122 2003 Jeep Liberty?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0122 2003 Jeep Liberty code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0122 2003 Jeep Liberty code?
Need more information on how to fix the P0122 2003 Jeep Liberty code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0122 2003 Jeep Liberty code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0122 2003 Jeep Liberty Code
1. What are the common symptoms of OBDII code P0122 in a 2003 Jeep Liberty?
The common symptoms of OBDII code P0122 in a 2003 Jeep Liberty include reduced engine power, hesitation or stalling when accelerating, and the vehicle going into "limp mode."
2. What are the possible causes of OBDII code P0122 in a 2003 Jeep Liberty?
Possible causes of OBDII code P0122 in a 2003 Jeep Liberty include a faulty throttle position sensor (TPS), damaged wiring or connectors in the TPS circuit, or a problem with the accelerator pedal position sensor.
3. How can I diagnose the throttle position sensor (TPS) in a 2003 Jeep Liberty?
To diagnose the TPS in a 2003 Jeep Liberty, you can use a multimeter to test the sensor's voltage output as you manually open and close the throttle. If the voltage readings are erratic or do not change smoothly, the TPS may be faulty.
4. Can a dirty throttle body cause OBDII code P0122 in a 2003 Jeep Liberty?
Yes, a dirty throttle body can potentially cause OBDII code P0122 in a 2003 Jeep Liberty. A buildup of carbon deposits or dirt on the throttle body can interfere with the TPS readings and cause incorrect voltage signals.
5. How can I repair OBDII code P0122 in a 2003 Jeep Liberty?
Repairing OBDII code P0122 in a 2003 Jeep Liberty typically involves replacing the faulty throttle position sensor (TPS) or repairing any damaged wiring or connectors in the TPS circuit. In some cases, cleaning the throttle body may also help resolve the issue.
6. Is it safe to continue driving a 2003 Jeep Liberty with OBDII code P0122?
It is not recommended to continue driving a 2003 Jeep Liberty with OBDII code P0122, as the reduced engine power and potential stalling can pose a safety risk. It is best to address the issue promptly to avoid further damage to the vehicle.
7. Can resetting the OBDII code P0122 in a 2003 Jeep Liberty make it go away permanently?
Resetting the OBDII code P0122 in a 2003 Jeep Liberty may temporarily clear the code, but if the underlying issue causing the code is not addressed, it is likely to reappear. It is important to diagnose and repair the root cause of the code to prevent it from coming back.
8. How much does it typically cost to repair OBDII code P0122 in a 2003 Jeep Liberty?
The cost to repair OBDII code P0122 in a 2003 Jeep Liberty can vary depending on the specific cause of the issue. Replacing a faulty throttle position sensor (TPS) or repairing wiring may cost anywhere from $100 to $300, including parts and labor.
9. Can a DIY enthusiast repair OBDII code P0122 in a 2003 Jeep Liberty?
Yes, a DIY enthusiast with some mechanical knowledge and the right tools can potentially repair OBDII code P0122 in a 2003 Jeep Liberty by replacing the throttle position sensor (TPS) or fixing wiring issues. However, if unsure, it's best to consult a professional mechanic for assistance.
10. Will OBDII code P0122 cause permanent damage to a 2003 Jeep Liberty if left unresolved?
If left unresolved, OBDII code P0122 in a 2003 Jeep Liberty can potentially cause further damage to the vehicle's engine or transmission over time. It is best to address the issue promptly to prevent any long-term damage.
Discuss the causes and fixes for P0122 2003 Jeep Liberty OBDII Code
Code P0122 2003 Jeep Liberty comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
