AutoCodes – Ford – P0106 2008 Ford Fusion

P0106 2008 Ford Fusion Code - Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance

Quick Answer

The Manifold Absolute Pressure (MAP) sensor measures the pressure inside the intake manifold. Common causes include Faulty Manifold Absolute Pressure (MAP) Sensor, Manifold Absolute Pressure Sensor harness is open or shorted, Manifold Absolute Pressure Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P0106 2008 Ford Fusion indicates Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance.
Common causes: Common causes include Faulty Manifold Absolute Pressure (MAP) Sensor, Manifold Absolute Pressure Sensor harness is open or shorted, Manifold Absolute Pressure Sensor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs Step-by-Step Diagnostic Guide My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 6,479

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 19, 2022

Description
Step-by-Step Diagnostic Guide
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0106 2008 Ford Fusion Description

The Manifold Absolute Pressure (MAP) sensor measures the pressure inside the intake manifold. Pressure in the intake manifold is affected by engine speed, throttle opening, air temperature, Barometric Pressure (BARO) and if equipped, turbocharger output. A diaphragm within the MAP sensor is displaced by the pressure changes that occur from the varying load and operating conditions of the engine. The sensor translates this action into electrical resistance.
The MAP sensor wiring includes 3 circuits. The Engine Control Module (ECM) supplies a regulated 5 volts to the sensor on a 5 V reference circuit. The ECM supplies ground on a low reference circuit. The MAP sensor provides a signal voltage to the ECM, relative to the pressure changes, on the MAP sensor signal circuit. The ECM converts the signal voltage input to a pressure value.
Under normal operation the greatest pressure that can exist in the intake manifold is at ignition ON, engine OFF, which is equal to the BARO. The lowest manifold pressure occurs when the vehicle is idling or decelerating. The ECM monitors the MAP sensor signal for pressure outside of the normal range.
The Diagnostic Trouble Code (DTC) will be set when the ECM determines the MAP Sensor is stuck within the normal operating range. It accomplishes this by running 3 different models within the software to determine the values.

OBDII Code P0106 2008 Ford Fusion - Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance - AutoCodes.com — P0106 2008 Ford Fusion Code - Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance

What does this mean?

What are the Possible Causes of the DTC P0106 2008 Ford Fusion?

Faulty Manifold Absolute Pressure (MAP) Sensor
Manifold Absolute Pressure Sensor harness is open or shorted
Manifold Absolute Pressure Sensor circuit poor electrical connection
Faulty Engine Control Module (ECM)

How to Fix the DTC P0106 2008 Ford Fusion?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

You can try to clean the MAP (Manifold Absolute Pressure) sensor with mass air flow sensor cleaner.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0106 2008 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0106 2008 Ford Fusion code?

Need more information on how to fix the P0106 2008 Ford Fusion code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0106 2008 Ford Fusion code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0106 2008 Ford Fusion Code

1. What are the common symptoms of OBDII code P0106 in a 2008 Ford Fusion?

- Common symptoms include poor engine performance, rough idling, stalling, decreased fuel efficiency, and the illumination of the Check Engine Light.

2. What does the OBDII code P0106 for a 2008 Ford Fusion indicate?

- The code P0106 signifies an issue with the Manifold Absolute Pressure (MAP) or Barometric Pressure Sensor, indicating a range/performance problem.

3. What are the possible causes of OBDII code P0106 on a 2008 Ford Fusion?

- Possible causes include a faulty MAP sensor, damaged sensor wiring, vacuum leaks, clogged air filter, intake manifold issues, or issues with the engine's computer system.

4. How can I diagnose the cause of OBDII code P0106 on my 2008 Ford Fusion?

- Diagnose the code by checking the MAP sensor's voltage output, inspecting the sensor and its wiring for damage, checking for vacuum leaks, and ensuring the air filter is clean and unobstructed.

5. Can I drive my 2008 Ford Fusion with OBDII code P0106?

- It is not recommended to drive the vehicle with code P0106 as it can lead to further engine damage and decreased performance. It's best to address the issue promptly.

6. How can I reset the OBDII code P0106 on my 2008 Ford Fusion?

- You can reset the code using an OBDII scanner or by disconnecting the car's battery for a few minutes. However, the underlying issue causing the code should be addressed to prevent it from reoccurring.

7. How much does it typically cost to repair OBDII code P0106 on a 2008 Ford Fusion?

- The cost of repair can vary depending on the specific cause of the issue. On average, it may cost between $100 and $300 for parts and labor to fix a P0106 code related to the MAP sensor.

8. Can I replace the MAP sensor myself to fix OBDII code P0106 on my 2008 Ford Fusion?

- Yes, replacing the MAP sensor is a relatively straightforward task that can be done by following the vehicle's repair manual or online guides. However, ensure you have the necessary tools and knowledge before attempting the repair.

9. Will OBDII code P0106 cause my 2008 Ford Fusion to fail an emissions test?

- Yes, a P0106 code can cause your vehicle to fail an emissions test as it indicates an issue with the vehicle's emissions control system. It's essential to address the problem before undergoing an emissions test.

10. Are there any preventive measures to avoid OBDII code P0106 in a 2008 Ford Fusion?

- To prevent OBDII code P0106, ensure regular maintenance of the vehicle, including checking and replacing air filters as needed, inspecting vacuum hoses for leaks, and addressing any engine performance issues promptly.