AutoCodes – Ford – P0060 2009 Ford Fusion

P0060 2009 Ford Fusion Code - HO2S Heater Resistance Bank 2 Sensor 2

Quick Answer

The Heated Oxygen Sensor (HO2S) must reach the operating temperature to provide an accurate voltage signal. Common causes include Faulty Heated Oxygen Sensor (HO2S) Bank 2 Sensor 2, Heated Oxygen Sensor Bank 2 Sensor 2 harness is open or shorted, Heated Oxygen Sensor Bank 2 Sensor 2 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

What it means: P0060 2009 Ford Fusion indicates HO2S Heater Resistance Bank 2 Sensor 2.
Common causes: Common causes include Faulty Heated Oxygen Sensor (HO2S) Bank 2 Sensor 2, Heated Oxygen Sensor Bank 2 Sensor 2 harness is open or shorted, Heated Oxygen Sensor Bank 2 Sensor 2 circuit poor electrical connection.
Severity: Moderate - service should be scheduled soon.
Can I drive?: The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 4,612

How popular is this code, among other codes? Low

Repair Importance Level

Moderate (Service soon) (2 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jul 13, 2020

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0060 2009 Ford Fusion Description

The Heated Oxygen Sensor (HO2S) must reach the operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensor to reach operating temperature. With the engine running, the ground is provided to the heater by the HO2S heater low control circuit through a low side driver within the Powertrain Control Module (PCM). The PCM commands the heater ON or OFF to maintain a specific HO2S operating temperature range. The PCM determines the temperature by measuring the current flow through the heater. When the heater is in the ON state, the PCM will pulse the heater OFF for 50 ms, once per second. The PCM calculates the heater resistance on a cold start. The Diagnostic Trouble Code (DTC) will set if the heater current requirements too low or high in the HO2S heater control circuit.

OBDII Code P0060 2009 Ford Fusion - HO2S Heater Resistance Bank 2 Sensor 2 - AutoCodes.com — P0060 2009 Ford Fusion Code - HO2S Heater Resistance Bank 2 Sensor 2

What does this mean?

What are the Possible Causes of the DTC P0060 2009 Ford Fusion?

Faulty Heated Oxygen Sensor (HO2S) Bank 2 Sensor 2
Heated Oxygen Sensor Bank 2 Sensor 2 harness is open or shorted
Heated Oxygen Sensor Bank 2 Sensor 2 circuit poor electrical connection
Faulty Powertrain Control Module (PCM)

How to Fix the DTC P0060 2009 Ford Fusion?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0060 2009 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0060 2009 Ford Fusion code?

Need more information on how to fix the P0060 2009 Ford Fusion code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0060 2009 Ford Fusion code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0060 2009 Ford Fusion Code

1. What are the common symptoms of OBDII code P0060 on a 2009 Ford Fusion?

- Common symptoms include poor fuel efficiency, rough idling, engine misfires, and the illumination of the Check Engine Light.

2. What does the OBDII code P0060 for a 2009 Ford Fusion indicate?

- The code P0060 indicates an issue with the HO2S (Heated Oxygen Sensor) heater circuit for Bank 2 Sensor 2.

3. What are the potential causes of OBDII code P0060 on a 2009 Ford Fusion?

- Possible causes include a faulty oxygen sensor, damaged wiring or connectors, a blown fuse, or a problem with the engine control module (ECM).

4. How can I diagnose the HO2S heater resistance issue on Bank 2 Sensor 2 of a 2009 Ford Fusion?

- Use a multimeter to test the resistance of the oxygen sensor's heater circuit and check for any continuity issues or abnormal resistance readings.

5. Can I still drive my 2009 Ford Fusion with OBDII code P0060 present?

- It is not recommended to drive the vehicle with this code as it can lead to poor engine performance and potential damage to the catalytic converter.

6. What is the typical repair for OBDII code P0060 on a 2009 Ford Fusion?

- The usual repair involves replacing the faulty oxygen sensor, repairing any damaged wiring or connectors, and resetting the fault code with an OBDII scanner.

7. Are there any DIY tips for fixing the HO2S heater resistance issue on Bank 2 Sensor 2 of a 2009 Ford Fusion?

- DIY enthusiasts can attempt to replace the oxygen sensor themselves by following detailed instructions provided in the vehicle's repair manual.

8. How much does it cost to repair OBDII code P0060 on a 2009 Ford Fusion at a professional mechanic's shop?

- Repair costs can vary depending on the labor rates and parts prices, but typically, fixing this issue can range from $200 to $500 at a mechanic's shop.

9. Can a dirty or contaminated oxygen sensor cause OBDII code P0060 on a 2009 Ford Fusion?

- While possible, a dirty or contaminated oxygen sensor is less likely to trigger code P0060. The issue is usually related to the sensor's heater circuit.

10. Is resetting the Check Engine Light after repairing OBDII code P0060 on a 2009 Ford Fusion necessary?

- Yes, it is recommended to reset the Check Engine Light using an OBDII scanner after fixing the issue to ensure that the repair was successful and to monitor for any new problems.