AutoCodes – Chevrolet – P0036 2014 Chevrolet Silverado

P0036 2014 Chevrolet Silverado Code - HO2S Heater Control Circuit Bank 1 Sensor 2

Quick Answer

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

What it means: P0036 2014 Chevrolet Silverado indicates HO2S Heater Control Circuit Bank 1 Sensor 2.
Common causes: Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection.
Severity: Moderate - service should be scheduled soon.
Can I drive?: The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

Save to My Repairs Step-by-Step Diagnostic Guide My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 799

How popular is this code, among other codes? Low

Repair Importance Level

Moderate (Service soon) (2 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Mar 25, 2024

Description
Step-by-Step Diagnostic Guide
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0036 2014 Chevrolet Silverado Description

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach an operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensors to reach operating temperature. Voltage is provided to the heater by an ignition voltage circuit through a fuse. With the engine running, the ground is provided to the heater by the HO2S heater low control circuit through a low side driver within the Engine Control Module (ECM). The ECM uses Pulse Width Modulation (PWM) to control the HO2S heater operation to maintain a specific HO2S operating temperature range.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects an open circuit in the heater output low side driver circuit of the heated oxygen sensor when the heater is commanded OFF for greater than 5 s.

OBDII Code P0036 2014 Chevrolet Silverado - HO2S Heater Control Circuit Bank 1 Sensor 2 - AutoCodes.com — P0036 2014 Chevrolet Silverado Code - HO2S Heater Control Circuit Bank 1 Sensor 2

What does this mean?

What are the Possible Causes of the DTC P0036 2014 Chevrolet Silverado?

Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground
Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection
Heated Oxygen Sensor Bank 1 Sensor 2 circuit fuse
Faulty Engine Control Module (ECM)

How to Fix the DTC P0036 2014 Chevrolet Silverado?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

The code means that there is a problem with the heater element circuit of the heated oxygen sensor. The control module monitors how long it takes the sensor to warm up and start sending an adequate signal. The code is set when the sensor is taking too long to warm up. Water getting inside the heated oxygen sensor connector can cause the heated oxygen sensor fuse to blow. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors. If the fuse and connector are OK, replacing the O2 Sensor usually takes care of the problem.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0036 2014 Chevrolet Silverado code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0036 2014 Chevrolet Silverado code?

Need more information on how to fix the P0036 2014 Chevrolet Silverado code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0036 2014 Chevrolet Silverado code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0036 2014 Chevrolet Silverado Code

1. What does the OBDII code P0036 on a 2014 Chevrolet Silverado mean?

The code P0036 refers to the HO2S Heater Control Circuit Bank 1 Sensor 2, indicating an issue with the oxygen sensor heater circuit in the downstream position on the same side as the number one cylinder.

2. What are the common symptoms of OBDII code P0036 in a 2014 Chevrolet Silverado?

Common symptoms associated with code P0036 include poor fuel efficiency, rough idling, engine misfires, and illuminated Check Engine Light on the dashboard.

3. What are the possible causes of OBDII code P0036 in a 2014 Chevrolet Silverado?

Possible causes of code P0036 include a faulty oxygen sensor, damaged wiring or connectors in the sensor circuit, a blown fuse, or issues with the engine control module (ECM).

4. How can I diagnose the OBDII code P0036 on my 2014 Chevrolet Silverado?

To diagnose code P0036, you can use an OBDII scanner to read the trouble code and examine the oxygen sensor's wiring, connectors, and heater circuit for any visible damage or loose connections.

5. How can I repair OBDII code P0036 in a 2014 Chevrolet Silverado?

The repair for code P0036 typically involves replacing the faulty oxygen sensor, repairing any damaged wiring or connectors, checking and replacing fuses if necessary, and resetting the Check Engine Light.

6. Can I continue driving my 2014 Chevrolet Silverado with OBDII code P0036?

While it may be possible to drive the vehicle with code P0036, it is not recommended as it can lead to decreased fuel efficiency, engine performance issues, and potential damage to the catalytic converter over time.

7. Is it safe to clear the OBDII code P0036 on a 2014 Chevrolet Silverado without fixing the issue?

Clearing the trouble code without addressing the underlying problem causing code P0036 is not recommended, as the issue will persist, potentially causing further damage and triggering the Check Engine Light again.

8. How much does it cost to repair OBDII code P0036 in a 2014 Chevrolet Silverado?

The cost of repairing code P0036 can vary depending on the cause of the issue, but it typically ranges from $150 to $400, including parts and labor.

9. Are there any preventive measures to avoid OBDII code P0036 in a 2014 Chevrolet Silverado?

Regularly maintaining your vehicle, including scheduled oxygen sensor inspections and replacements as recommended by the manufacturer, can help prevent issues like code P0036 from occurring.

10. Can a DIY enthusiast fix OBDII code P0036 in a 2014 Chevrolet Silverado?

While some experienced DIY enthusiasts may be able to address code P0036 by replacing the oxygen sensor or checking the wiring, it is recommended to consult a professional mechanic for an accurate diagnosis and repair.