P0019 Buick Code - Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor 'B'
Quick Answer
The Crankshaft Position (CKP) sensor is a permanent magnet generator, known as a variable reluctance sensor. Common causes include Mechanical timing fault, Blocked oil passage, Low oil level. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0019 Buick indicates Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor 'B'.
- Common causes
- Common causes include Mechanical timing fault, Blocked oil passage, Low oil level.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0019 Buick Description
The Camshaft Position (CMP) sensor is triggered by a notched reluctor wheel built into the exhaust camshaft sprocket. The CMP sensor provides 6 signal pulses every camshaft revolution. Each notch or feature of the reluctor wheel is of different size for individual cylinder identification. This means the CMP and crankshaft position (CKP) signals are pulse width encoded to enable the PCM to constantly monitor their relationship. This relationship is used to determine the camshaft actuator position and control its phasing at the correct value. The PCM also uses this signal to identify the compression stroke of each cylinder, and for sequential fuel injection. The CMP sensor is connected to the PCM by a 12-volt, low reference, and signal circuit.
What are the Possible Causes of the DTC P0019 Buick?
- Mechanical timing fault
- Blocked oil passage
- Low oil level
- Faulty Exhaust ('B') Camshaft Position (CMP) Sensor
- Faulty Crankshaft Position (CKP) Sensor
How to Fix the DTC P0019 Buick?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
2007 Buick Allure
2007-2012 Buick LaCrosse
2008-2012 Buick Enclave
Buick Factory Service Bulletin OBDII Code P0019
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0019 Buick code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0019 Buick code?
Need more information on how to fix the P0019 Buick code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0019 Buick code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0019 Buick Code
1. What are the common symptoms of OBDII code P0019 in a Buick?
The common symptoms of OBDII code P0019 in a Buick include rough idling, engine misfires, poor acceleration, and the illumination of the Check Engine Light.
2. What does the OBDII code P0019 in a Buick indicate?
OBDII code P0019 in a Buick indicates a problem with the correlation between the crankshaft position sensor and the camshaft position sensor on Bank 2 Sensor 'B'.
3. What are the possible causes of OBDII code P0019 in a Buick?
Possible causes of OBDII code P0019 in a Buick include a faulty camshaft position sensor, a faulty crankshaft position sensor, timing chain or belt issues, engine mechanical problems, or electrical wiring issues.
4. How can I diagnose OBDII code P0019 in my Buick?
Diagnosing OBDII code P0019 in your Buick involves using a scan tool to read the code, checking the camshaft and crankshaft position sensor readings, inspecting the timing chain or belt, and performing a visual inspection of the sensor wiring.
5. What are some repair tips for addressing OBDII code P0019 in a Buick?
Repair tips for addressing OBDII code P0019 in a Buick include replacing the faulty camshaft or crankshaft position sensor, fixing any timing chain or belt issues, addressing engine mechanical problems, and repairing any damaged wiring.
6. Can driving with OBDII code P0019 in a Buick cause further damage?
Driving with OBDII code P0019 in a Buick can potentially cause further damage to the engine if left unresolved. It is recommended to address the issue promptly to avoid more severe problems.
7. How much does it cost to fix OBDII code P0019 in a Buick?
The cost to fix OBDII code P0019 in a Buick can vary depending on the underlying cause of the issue. Repairs may range from a few hundred dollars for sensor replacements to more significant costs for timing chain or belt repairs.
8. Can I reset the Check Engine Light after fixing OBDII code P0019 in my Buick?
After fixing OBDII code P0019 in your Buick, you can reset the Check Engine Light using a scan tool to clear the trouble code. This will turn off the light and allow you to monitor if the issue reoccurs.
9. Is it safe to drive my Buick with OBDII code P0019 present?
It is not recommended to drive your Buick with OBDII code P0019 present, as it can lead to poor engine performance and potential damage. It is best to address the issue promptly to ensure safe and reliable driving.
10. How often does OBDII code P0019 occur in Buick vehicles?
OBDII code P0019 can occur in Buick vehicles, particularly in models equipped with camshaft and crankshaft position sensors. While not extremely common, it is important to be aware of the symptoms and causes associated with this code.
Discuss the causes and fixes for P0019 Buick OBDII Code
Code P0019 Buick comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
