P0011 Hyundai Code - 'A' Camshaft Position Timing Over-Advanced Or System Performance Bank 1
Quick Answer
The CVVT (Continuously Variable Valve Timing) system is installed to the chain sprocket of the exhaust camshaft. Common causes include Low or Dirty Engine Oil, Faulty Valve Timing Control (VTC), Valve Timing Control (VTC) harness is open or shorted circuit. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0011 Hyundai indicates 'A' Camshaft Position Timing Over-Advanced Or System Performance Bank 1.
- Common causes
- Common causes include Low or Dirty Engine Oil, Faulty Valve Timing Control (VTC), Valve Timing Control (VTC) harness is open or shorted circuit.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0011 Hyundai Description
The deviation of the camshaft position from the target point is evaluated during stable driving condition. The Engine Control Module (ECM) accumulates this deviation for a certain period and sets DTC P0011 when the accumulated deviation is too high. The target camshaft position is predetermined value depending on engine speed and throttle angle in the ECM.
What are the Possible Causes of the DTC P0011 Hyundai?
- Low or Dirty Engine Oil
- Faulty Valve Timing Control (VTC)
- Valve Timing Control (VTC) harness is open or shorted circuit.
- Valve Timing Control (VTC) circuit poor electrical connector
- Incorrect timing
- Engine mechanical problems
- Damaged Engine Control Module (ECM)
How to Fix the DTC P0011 Hyundai?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
Hyundai Accent (MC)
Hyundai 2003-2006 SULEV Elantra (XD)
Hyundai 2004-2008 Tiburon 2.0L (GK)
Hyundai Tucson 2.0L (JM)
Hyundai Elantra (HD)
Hyundai Elantra Touring (FD)
Hyundai Genesis Coupe (BK)
Hyundai Sonata (NF)
Hyundai Santa Fe
Hyundai Sonata (NF)
Hyundai Santa Fe (CM)
Hyundai Azera (TG)
Hyundai Veracruz (EN)
Hyundai Entourage (EP),
Hyundai Genesis Coupe (BK)
Hyundai Genesis Sedan (BH)Genesis Sedan (BH)
The bulletin provides information on how to inspect and diagnose problems related to the Oil Control Valve (OCV) used in Constant Variable Valve Timing (CVVT), if at any time the OCV is suspected as the caused of rough idling, poor acceleration, camshaft timing misalignment-related trouble codes, misfire-related trouble codes.
Factory Service Bulletin: Hyundai Constant Variable Valve Timing Oil Control Valve Inspection OBDII Code P0011
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0011 Hyundai code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0011 Hyundai code?
Need more information on how to fix the P0011 Hyundai code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0011 Hyundai code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0011 Hyundai Code
1. What are common symptoms of OBDII code P0011 on a Hyundai?
- Common symptoms include rough idling, reduced engine performance, poor fuel efficiency, and the illumination of the check engine light.
2. What does the OBDII code P0011 on a Hyundai indicate?
- The code indicates that the 'A' camshaft position timing is over-advanced or that there is a performance issue in Bank 1 of the engine.
3. What are some possible causes of OBDII code P0011 on a Hyundai?
- Possible causes include issues with the camshaft timing, a faulty camshaft position sensor, problems with the variable valve timing (VVT) system, or engine oil issues.
4. How serious is OBDII code P0011 on a Hyundai?
- While the vehicle may still be driveable with this code, it is important to address it promptly to prevent potential damage to the engine and ensure optimal performance.
5. How can I diagnose OBDII code P0011 on my Hyundai?
- Diagnosis typically involves using a scan tool to read the code, checking the camshaft position sensor, inspecting the VVT system, and examining the engine oil level and condition.
6. Can I continue driving my Hyundai with OBDII code P0011?
- It is generally not recommended to drive for an extended period with this code active, as it can lead to decreased engine performance and potential long-term damage.
7. How can I repair OBDII code P0011 on my Hyundai?
- Repair options may include replacing the camshaft position sensor, repairing or replacing the VVT system components, ensuring proper engine oil levels and quality, and resetting the code with a scan tool.
8. Will resetting the OBDII code P0011 on my Hyundai make it disappear permanently?
- Resetting the code may temporarily turn off the check engine light, but if the underlying issue causing the code is not addressed, the light is likely to come back on.
9. Can a DIY enthusiast fix OBDII code P0011 on a Hyundai?
- Depending on their skill level and access to tools, a DIY enthusiast may be able to address some aspects of this code, such as sensor replacement or basic system checks.
10. How much does it typically cost to repair OBDII code P0011 on a Hyundai?
- The cost of repairs can vary depending on the specific cause of the code and the labor rates in your area, but it is advisable to consult with a mechanic for an accurate estimate.
Discuss the causes and fixes for P0011 Hyundai OBDII Code
-
The engine oil initially was @ 3/4 full. As whether the oil was dirty is not likely as it was replaced 2 months back. Incorrect timing was not likely as the engine timing belt has not been touched. Most likely the Actuator and Oil Pressure r the main cause of the fault code. Will confirm again once the relevant parts r replaced and tested.
-
Check engine light came on during road trip. Turns out the oil dipstick was dry. Added oil and found P0011 with reader once I got home. Attributing check light to low oil since confirming code on this site. Thanks.
-
Our 2007 Sonata check engine light has been going on and off for several years. We passed the first emission test 2 yrs ago after changing the oil. The light was on before the oil change, went off after, had the car tested a week later and it passed. Just got our second emission notice. Tested it while the light was on and code P0011 showed up. We paid a garage $95 to check it out and they had a "hunch" it was a solenoid and they wanted over $300 to fix it. We did the oil change that was due instead. The light went off for a few days but then back on again. We waited a couple weeks and when the light went off again we immediately took it for a retest and it passed.
-
check engine light came off and on for a long time now. had oil changed and light stays on now. what is it
-
Its possible that you used the wrong oil thickness, that could cause the P0011 code to set.
-
My Check Engine light won't go off on my 2007 Sonata.. I got an oil change after finding out that the code P0011 was showing up hoping that it was just dirty oil but that isn't the issue.. I'm not car smart so I don't understand what any of this means.. Help please?
-
The code means that the systems that advance and retards the engine timing (engine advance and retards the timing to save gas) is not working properly. Usually the problem is a sticking valve. The valve gets sticky due to dirty oil or lack of oil changes.
If you already change the oil and the problem still exists, then you can either wait sometime (may need a couple of oil changes to get the valve unstuck) or just change the valve.
-
Saludos, me podrías decir que tipo de Soleoinde es compatible con una Nissan Versa 2009 SL 1.8 Transmision CVT
-
How much would it take to fix an issue like this? I am looking at buying an 06 Sonata with either the System Performance Bank 1 as the issue or Camshaft position timing over advanced (code: P0011). I am trying to determine a ballpark of how much it'll cost me to fix her up.
-
It was $300 including labor and had to get both OCV(Selnoid) & Camshaft position sensor changed on my Elantra
-
It was $300 including labor and had to get both OCV(Selnoid) & Camshaft position sensor changed on my Elantra.
-
I had the same problem with Tuscon. I found the ocv filter needed cleaning. Once I did this, all was OK. ?
-
How long after you added oil did the check engine light take to go off? I just got oil changed this evening. Light came on this afternoon
-
2007 Hyundai Tucson. Had timing belt and water pump changed. Engine became hard to start almost immediately. Mechanic told me VVT needed to be changed. This did not solve the starting problem, but now Check Engine light came on with P0011 code….what gives?
-
Sounds like the timing belt was not properly installed. The symptoms of your problem, hard start en engine code P0011, are the most common when the timing belt is installed out of time.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
