P0010 2015 GMC Sierra Code - Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1
Quick Answer
The Camshaft Position (CMP) actuator system enables the Engine Control Module (ECM) to change the timing of the camshafts while the engine is operating. Common causes include Dirty Oil, Low engine oil level, Faulty Intake Camshaft Position Actuator Solenoid Valve Bank 1. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0010 2015 GMC Sierra indicates Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1.
- Common causes
- Common causes include Dirty Oil, Low engine oil level, Faulty Intake Camshaft Position Actuator Solenoid Valve Bank 1.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0010 2015 GMC Sierra Description
Ignition voltage is supplied directly to the Camshaft Position Actuator Solenoid Valve. The ECM controls the solenoid valve by grounding the control circuit with a solid-state device called a driver. The driver is equipped with a feedback circuit that is pulled up to a voltage. The ECM can determine if the control circuit is open, shorted to the ground, or shorted to a voltage by monitoring the feedback voltage.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects an open solenoid circuit in the CMP actuator for greater than 1 second or a cumulative of 5 seconds when the solenoid is commanded OFF.
The ECM monitors the control circuit of the CMP actuator solenoid for electrical faults. The ECM can determine if a control circuit is open, shorted high, or shorted low. If the ECM detects a fault with the CMP actuator solenoid control, DTC P0010 will set.
What are the Possible Causes of the DTC P0010 2015 GMC Sierra?
- Dirty Oil
- Low engine oil level
- Faulty Intake Camshaft Position Actuator Solenoid Valve Bank 1
- Intake Camshaft Position Actuator Solenoid Valve Bank 1 harness is open or shorted
- Intake Camshaft Position Actuator Solenoid Valve Bank 1 circuit poor electrical connection
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0010 2015 GMC Sierra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0010 2015 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0010 2015 GMC Sierra code?
Need more information on how to fix the P0010 2015 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0010 2015 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0010 2015 GMC Sierra Code
1. What does the OBDII code P0010 mean on a 2015 GMC Sierra?
P0010 indicates an issue with the "Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1," meaning the engine control module (ECM) has detected a problem with the intake camshaft timing.
2. What are the common symptoms of code P0010 on a 2015 GMC Sierra?
Common symptoms include rough idling, poor acceleration, reduced fuel efficiency, engine misfires, and, in some cases, the engine failing to start.
3. What causes the P0010 code on a 2015 GMC Sierra?
The most common causes are a faulty intake camshaft actuator solenoid, damaged wiring or connectors, low engine oil level or oil contamination, or a malfunctioning ECM.
4. How serious is the P0010 code on a 2015 GMC Sierra?
While the vehicle may still run, driving with a P0010 code can lead to poor performance and potentially cause internal engine damage if not addressed promptly.
5. How do you diagnose the P0010 code on a 2015 GMC Sierra?
Diagnosis typically involves scanning the ECM for codes, inspecting the intake camshaft actuator solenoid and wiring, checking the engine oil level and condition, and testing the solenoid with a multimeter.
6. Can I fix the P0010 code on my 2015 GMC Sierra myself?
If you're experienced with car repairs, you can try replacing the intake camshaft actuator solenoid or fixing damaged wiring. However, professional diagnosis is recommended if you're unsure.
7. How much does it cost to repair the P0010 code on a 2015 GMC Sierra?
Replacing the intake camshaft actuator solenoid typically costs between $100 and $300, including parts and labor, depending on the repair shop and region.
8. Can low or dirty engine oil cause the P0010 code on a 2015 GMC Sierra?
Yes, low or dirty engine oil can cause the solenoid to malfunction, leading to a P0010 code. Always ensure the engine oil is at the correct level and replaced at regular intervals.
9. Where is the intake camshaft actuator solenoid located on a 2015 GMC Sierra?
The intake camshaft actuator solenoid is located on the engine, usually near the front of the cylinder head on the Bank 1 side (the side with cylinder 1).
10. Will clearing the P0010 code fix the issue on a 2015 GMC Sierra?
Clearing the code may turn off the check engine light temporarily, but the underlying problem must be fixed to prevent the code from returning.
Discuss the causes and fixes for P0010 2015 GMC Sierra OBDII Code
Code P0010 2015 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
