C1336 Scion Code - Zero Point Calibration of Acceleration Sensor Undone
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) receives signals from the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) via the Controller Area Network (CAN) communication system. Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly). Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1336 Scion indicates Zero Point Calibration of Acceleration Sensor Undone.
- Common causes
- Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly).
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1336 Scion Description
The Airbag Sensor Assembly has a built-in Yaw Rate Sensor and Acceleration Sensor and detects the vehicle's condition. If there is trouble in the bus lines between the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.
The Diagnostic Trouble Code (DTC) is also output when the calibration has not been completed.
What are the Possible Causes of the DTC C1336 Scion?
- Acceleration Sensor Calibration
- Sensor installation
- Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly)
- Airbag Sensor Assembly harness is open or shorted
- Airbag Sensor Assembly circuit poor electrical connection
- Faulty Skid Control ECU (Brake Actuator Assembly)
How to Fix the DTC C1336 Scion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1336 Scion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1336 Scion code?
Need more information on how to fix the C1336 Scion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1336 Scion code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1336 Scion Code
1. What does OBDII code C1336 in a Scion mean?
The code C1336 in a Scion indicates that the zero point calibration of the acceleration sensor has not been completed.
2. What are the common symptoms of OBDII code C1336 in a Scion?
Common symptoms of code C1336 may include the check engine light illuminating on the dashboard and potential issues with the vehicle's stability control system.
3. What causes the OBDII code C1336 in a Scion?
The most common cause of code C1336 is a failure to complete the zero point calibration of the acceleration sensor, which is necessary for proper operation of the vehicle's stability control system.
4. How can I repair OBDII code C1336 in a Scion?
To repair code C1336, the zero point calibration of the acceleration sensor needs to be completed using a diagnostic scan tool or by following the manufacturer's recommended procedure.
5. Can I drive my Scion with OBDII code C1336?
It is generally not recommended to drive a vehicle with an unresolved OBDII code, including code C1336, as it may lead to further issues with the vehicle's stability control system.
6. How do I perform the zero point calibration of the acceleration sensor in a Scion?
The zero point calibration procedure for the acceleration sensor in a Scion typically involves following specific steps outlined in the vehicle's service manual or using a diagnostic scan tool.
7. Can a DIY enthusiast perform the zero point calibration for OBDII code C1336 in a Scion?
Performing the zero point calibration for code C1336 may require specialized tools and knowledge, so it is recommended to consult a professional mechanic or dealership for proper calibration.
8. Will resetting the OBDII code C1336 in a Scion resolve the issue?
Simply resetting the code may temporarily turn off the check engine light, but it will not address the underlying problem of the acceleration sensor calibration needing to be completed.
9. How long does it take to complete the zero point calibration for OBDII code C1336 in a Scion?
The time it takes to perform the zero point calibration can vary depending on the specific Scion model and the method used, but it typically takes around 15-30 minutes.
10. Is OBDII code C1336 in a Scion a serious issue?
While code C1336 may not cause immediate safety concerns, it is important to address this issue promptly to ensure the proper functioning of the vehicle's stability control system.
Discuss the causes and fixes for C1336 Scion OBDII Code
Code C1336 Scion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
