C1336 2018 Toyota RAV4 Code - Zero Point Calibration of Acceleration Sensor Undone
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) receives signals from the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) via the Controller Area Network (CAN) communication system. Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly). Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1336 2018 Toyota RAV4 indicates Zero Point Calibration of Acceleration Sensor Undone.
- Common causes
- Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly).
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1336 2018 Toyota RAV4 Description
The Airbag Sensor Assembly has a built-in Yaw Rate Sensor and Acceleration Sensor and detects the vehicle's condition. If there is trouble in the bus lines between the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.
The Diagnostic Trouble Code (DTC) is also output when the calibration has not been completed.
What are the Possible Causes of the DTC C1336 2018 Toyota RAV4?
- Acceleration Sensor Calibration
- Sensor installation
- Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly)
- Airbag Sensor Assembly harness is open or shorted
- Airbag Sensor Assembly circuit poor electrical connection
- Faulty Skid Control ECU (Brake Actuator Assembly)
How to Fix the DTC C1336 2018 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1336 2018 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1336 2018 Toyota RAV4 code?
Need more information on how to fix the C1336 2018 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1336 2018 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1336 2018 Toyota RAV4 Code
1. What does OBDII code C1336 mean on a 2018 Toyota RAV4?
The code C1336 indicates that the Zero Point Calibration of the Acceleration Sensor is incomplete on a 2018 Toyota RAV4.
2. What are the common symptoms of OBDII code C1336 on a 2018 Toyota RAV4?
Common symptoms include the traction control light staying on, the ABS light being illuminated, and potential issues with the vehicle stability control system.
3. What are the possible causes of OBDII code C1336 on a 2018 Toyota RAV4?
The primary cause of this code is a failure to properly calibrate the acceleration sensor, which may occur after certain maintenance procedures or component replacements.
4. How can I repair OBDII code C1336 on my 2018 Toyota RAV4?
To resolve this issue, the Zero Point Calibration of the Acceleration Sensor must be performed using a compatible diagnostic tool, following the manufacturer's specified procedure.
5. Can I perform the Zero Point Calibration myself to clear OBDII code C1336 on my 2018 Toyota RAV4?
While it is possible to attempt the calibration yourself, it is recommended to have it done by a qualified technician with the proper tools and expertise to ensure accurate and successful calibration.
6. Is it safe to continue driving with OBDII code C1336 on a 2018 Toyota RAV4?
It is not advisable to continue driving with this code active, as it may affect the vehicle's stability control system and compromise overall safety. It is recommended to address the issue promptly.
7. How long does the Zero Point Calibration procedure take for OBDII code C1336 on a 2018 Toyota RAV4?
The calibration process typically takes around 15-30 minutes to complete, but this can vary depending on the diagnostic equipment and technician's familiarity with the procedure.
8. Will performing the Zero Point Calibration clear the OBDII code C1336 immediately on a 2018 Toyota RAV4?
In most cases, once the calibration is successfully completed, the code should be cleared automatically. However, some vehicles may require additional steps to reset the code.
9. Can a low battery affect the Zero Point Calibration for OBDII code C1336 on a 2018 Toyota RAV4?
Yes, a low or weak battery can potentially interfere with the calibration process, so it is important to ensure the vehicle's battery is in good condition before attempting the calibration.
10. Are there any DIY methods to troubleshoot or reset OBDII code C1336 on a 2018 Toyota RAV4?
While there are no recommended DIY methods to reset this code, ensuring the battery is charged and in good condition before attempting the calibration may help prevent any potential issues.
Discuss the causes and fixes for C1336 2018 Toyota RAV4 OBDII Code
Code C1336 2018 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
