C1336 2015 Toyota RAV4 Code - Zero Point Calibration of Acceleration Sensor Undone
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) receives signals from the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) via the Controller Area Network (CAN) communication system. Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly). Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1336 2015 Toyota RAV4 indicates Zero Point Calibration of Acceleration Sensor Undone.
- Common causes
- Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly).
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1336 2015 Toyota RAV4 Description
The Airbag Sensor Assembly has a built-in Yaw Rate Sensor and Acceleration Sensor and detects the vehicle's condition. If there is trouble in the bus lines between the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.
The Diagnostic Trouble Code (DTC) is also output when the calibration has not been completed.
What are the Possible Causes of the DTC C1336 2015 Toyota RAV4?
- Acceleration Sensor Calibration
- Sensor installation
- Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly)
- Airbag Sensor Assembly harness is open or shorted
- Airbag Sensor Assembly circuit poor electrical connection
- Faulty Skid Control ECU (Brake Actuator Assembly)
How to Fix the DTC C1336 2015 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1336 2015 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1336 2015 Toyota RAV4 code?
Need more information on how to fix the C1336 2015 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1336 2015 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1336 2015 Toyota RAV4 Code
1. What does the OBDII code C1336 on my 2015 Toyota RAV4 mean?
The code C1336 indicates that the Zero Point Calibration of the Acceleration Sensor is undone.
2. What are the common symptoms of OBDII code C1336 in a 2015 Toyota RAV4?
Common symptoms include the check engine light being illuminated on the dashboard and possible issues with the vehicle's stability control system.
3. What could cause the Zero Point Calibration of the Acceleration Sensor to be undone in a 2015 Toyota RAV4?
The calibration may become undone due to a dead or weak battery, electrical issues, or a malfunction in the acceleration sensor itself.
4. How can I reset the Zero Point Calibration of the Acceleration Sensor in my 2015 Toyota RAV4?
To reset the calibration, a specific procedure involving turning the steering wheel and driving the vehicle in a straight line at a certain speed may be required. Consult your vehicle's manual or a professional mechanic for detailed instructions.
5. Can I drive my 2015 Toyota RAV4 with the OBDII code C1336 present?
It is generally safe to drive with this code, but it is recommended to address the underlying issue promptly to ensure the stability control system functions properly.
6. Is it possible to clear the OBDII code C1336 in a 2015 Toyota RAV4 without performing the calibration?
Clearing the code without calibrating the sensor may temporarily turn off the check engine light, but the issue causing the code will likely persist and may trigger the code again.
7. How much does it typically cost to repair the Zero Point Calibration issue in a 2015 Toyota RAV4?
The cost of repairing the calibration issue can vary depending on the root cause. It is recommended to get a diagnostic from a professional mechanic to determine the exact repair cost.
8. Can a DIY enthusiast perform the Zero Point Calibration on a 2015 Toyota RAV4?
While it is possible for some individuals to perform the calibration themselves, it is recommended to consult the vehicle's manual or seek guidance from a qualified mechanic to ensure proper execution.
9. Will the OBDII code C1336 disappear on its own in a 2015 Toyota RAV4?
The code may not disappear on its own unless the underlying issue is resolved and the calibration is successfully reset.
10. How often does the Zero Point Calibration of the Acceleration Sensor need to be performed in a 2015 Toyota RAV4?
The calibration typically needs to be performed when specific maintenance or repair work is done on the vehicle, or if the system detects an issue with the sensor.
Discuss the causes and fixes for C1336 2015 Toyota RAV4 OBDII Code
Code C1336 2015 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
