C1290 2013 Toyota RAV4 Code - Steering Angle Sensor Zero Point Malfunction
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) acquires steering sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. Common causes include Yaw rate and deceleration sensor zero point calibration incomplete, Poor adjustment of centered position of the steering wheel, Poor adjustment of front wheel alignment. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1290 2013 Toyota RAV4 indicates Steering Angle Sensor Zero Point Malfunction.
- Common causes
- Common causes include Yaw rate and deceleration sensor zero point calibration incomplete, Poor adjustment of centered position of the steering wheel, Poor adjustment of front wheel alignment.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1290 2013 Toyota RAV4 Description
If front wheel alignment or steering wheel position is adjusted without disconnecting the negative battery terminal, or if the yaw rate and acceleration sensor zero point is not acquired after the adjustments have been completed, the Skid Control ECU (Brake Actuator Assembly) detects the difference between the previous zero point and newly acquired zero point and outputs this Diagnostic Trouble Code (DTC) to indicate a poor adjustment.
The steering sensor zero point malfunction warning will be canceled by turning the ignition switch off.
What are the Possible Causes of the DTC C1290 2013 Toyota RAV4?
- Yaw rate and deceleration sensor zero point calibration incomplete
- Poor adjustment of centered position of the steering wheel
- Poor adjustment of front wheel alignment
How to Fix the DTC C1290 2013 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1290 2013 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1290 2013 Toyota RAV4 code?
Need more information on how to fix the C1290 2013 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1290 2013 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1290 2013 Toyota RAV4 Code
1. What are the common symptoms of OBDII code C1290 in a 2013 Toyota RAV4?
The common symptoms of OBDII code C1290 (Steering Angle Sensor Zero Point Malfunction) in a 2013 Toyota RAV4 include the traction control light or ABS light illuminating on the dashboard.
2. What could cause the Steering Angle Sensor Zero Point Malfunction in a 2013 Toyota RAV4?
The Steering Angle Sensor Zero Point Malfunction in a 2013 Toyota RAV4 can be caused by a faulty steering angle sensor, damaged wiring, or a calibration issue.
3. How serious is the Steering Angle Sensor Zero Point Malfunction in a 2013 Toyota RAV4?
The Steering Angle Sensor Zero Point Malfunction should be addressed promptly as it can affect the proper functioning of the vehicle's traction control system and ABS, impacting overall safety.
4. Can I continue driving my 2013 Toyota RAV4 with the C1290 code present?
It is not recommended to continue driving your 2013 Toyota RAV4 with the C1290 code present as it may compromise the vehicle's stability control systems.
5. How can I diagnose the Steering Angle Sensor Zero Point Malfunction in my 2013 Toyota RAV4?
Diagnosing the Steering Angle Sensor Zero Point Malfunction typically involves using an OBDII scanner to read the specific trouble code, followed by inspecting the steering angle sensor and its wiring for any issues.
6. Is it possible to reset the Steering Angle Sensor Zero Point Malfunction code in a 2013 Toyota RAV4?
Simply resetting the code may not fix the underlying issue causing the Steering Angle Sensor Zero Point Malfunction in a 2013 Toyota RAV4. It's essential to diagnose and address the root cause.
7. Can a DIY enthusiast repair the Steering Angle Sensor Zero Point Malfunction in a 2013 Toyota RAV4?
Repairing the Steering Angle Sensor Zero Point Malfunction may require specialized tools and expertise, so it is recommended to consult a professional mechanic for proper diagnosis and repair.
8. How much does it typically cost to repair the Steering Angle Sensor Zero Point Malfunction in a 2013 Toyota RAV4?
The cost of repairing the Steering Angle Sensor Zero Point Malfunction in a 2013 Toyota RAV4 can vary depending on the exact cause of the issue, but it may involve sensor replacement, wiring repairs, or calibration, potentially costing a few hundred dollars.
9. Will fixing the Steering Angle Sensor Zero Point Malfunction turn off the warning lights on my 2013 Toyota RAV4?
Once the underlying issue causing the Steering Angle Sensor Zero Point Malfunction is fixed and the system is recalibrated, the warning lights on the dashboard should reset.
10. How often does the Steering Angle Sensor Zero Point Malfunction occur in 2013 Toyota RAV4 vehicles?
The Steering Angle Sensor Zero Point Malfunction can occur in 2013 Toyota RAV4 vehicles due to sensor wear, wiring issues, or calibration problems, but it is not considered a common occurrence.
Discuss the causes and fixes for C1290 2013 Toyota RAV4 OBDII Code
Code C1290 2013 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
