C1248 Chevrolet Code - Dynamic Rear Proportioning Control System
Quick Answer
Dynamic Rear Proportioning (DRP) is a control system that replaces the hydraulic proportioning function of the mechanical proportioning valve in the base brake system. Common causes include Faulty Electronic Brake Control Module (EBCM), Electronic Brake Control Module (EBCM) harness is open or shorted, Electronic Brake Control Module (EBCM) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1248 Chevrolet indicates Dynamic Rear Proportioning Control System.
- Common causes
- Common causes include Faulty Electronic Brake Control Module (EBCM), Electronic Brake Control Module (EBCM) harness is open or shorted, Electronic Brake Control Module (EBCM) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1248 Chevrolet Description
The C1248 code will set when DTC C1214, C1217, C1237, C1254, C1255, C1261-1268, or C1271-1274 sets, DTC C1236 sets and system voltage is less than 8.5 volts, or two wheel speed sensor DTCs on same axle set.
What are the Possible Causes of the DTC C1248 Chevrolet?
- Faulty Electronic Brake Control Module (EBCM)
- Electronic Brake Control Module (EBCM) harness is open or shorted
- Electronic Brake Control Module (EBCM) circuit poor electrical connection
How to Fix the DTC C1248 Chevrolet?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1248 Chevrolet code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1248 Chevrolet code?
Need more information on how to fix the C1248 Chevrolet code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1248 Chevrolet code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1248 Chevrolet Code
1. What are the common symptoms of OBDII code C1248 in a Chevrolet related to the Dynamic Rear Proportioning Control System?
- Common symptoms include the ABS warning light being illuminated on the dashboard, increased stopping distances, and potential loss of vehicle stability during braking.
2. What does OBDII code C1248 indicate in a Chevrolet regarding the Dynamic Rear Proportioning Control System?
- OBDII code C1248 signifies a malfunction in the Dynamic Rear Proportioning Control System, which is responsible for adjusting rear brake pressure distribution for optimal braking performance.
3. What are the possible causes of OBDII code C1248 in a Chevrolet related to the Dynamic Rear Proportioning Control System?
- Possible causes include a faulty rear wheel speed sensor, issues with the rear brake pressure modulator valve, wiring problems, or a malfunction in the Electronic Brake Control Module (EBCM).
4. How can I diagnose the OBDII code C1248 in a Chevrolet with regards to the Dynamic Rear Proportioning Control System?
- Diagnosis typically involves using a diagnostic scanner to retrieve the trouble codes, conducting a visual inspection of the system components, and performing specific tests outlined in the manufacturer's service manual.
5. Is it safe to continue driving my Chevrolet with OBDII code C1248 related to the Dynamic Rear Proportioning Control System?
- It is not recommended to drive the vehicle with this code present, as it can affect the proper functioning of the braking system and compromise overall safety. Immediate attention and repair are advised.
6. Can I reset the OBDII code C1248 in my Chevrolet related to the Dynamic Rear Proportioning Control System by disconnecting the battery?
- While disconnecting the battery might clear the code temporarily, it will not fix the underlying issue causing the fault. It is important to diagnose and repair the root cause of the problem to prevent the code from reoccurring.
7. How can I repair OBDII code C1248 in my Chevrolet associated with the Dynamic Rear Proportioning Control System?
- Repair methods may include replacing the faulty rear wheel speed sensor, addressing wiring issues, replacing the rear brake pressure modulator valve, or reprogramming the EBCM. Professional assistance may be required for accurate diagnosis and repair.
8. Can extreme weather conditions or rough driving terrain trigger OBDII code C1248 in a Chevrolet related to the Dynamic Rear Proportioning Control System?
- Yes, harsh driving conditions or severe weather can potentially cause damage to the components of the Dynamic Rear Proportioning Control System, leading to the triggering of OBDII code C1248.
9. How much does it typically cost to repair OBDII code C1248 in a Chevrolet linked to the Dynamic Rear Proportioning Control System?
- The cost of repair can vary depending on the exact cause of the issue and the extent of the repairs needed. It is advisable to consult a mechanic or dealership for a detailed diagnosis and cost estimate.
10. Are there any preventive maintenance steps I can take to avoid encountering OBDII code C1248 in my Chevrolet related to the Dynamic Rear Proportioning Control System?
- Regularly inspecting the braking system, including sensors and wiring, and promptly addressing any issues can help prevent the occurrence of OBDII code C1248. Following the manufacturer's recommended maintenance schedule is also crucial in maintaining system health.
Discuss the causes and fixes for C1248 Chevrolet OBDII Code
-
On my o4 avalanche brake light and abs light comes on and service brake system message displays what could it be
-
There are many things that can set the Brake and ABS warning lights, the first step is to check for codes with an OBDII scanner. With a code you can get a better idea what the problem is.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
