C1012 Ford Code - Brake Pedal Feel Simulator Cut-Off Valve Solenoid general Electrical Failure
Quick Answer
The brake pedal feel simulator cut-off solenoid valve and brake pedal feel simulator cut-off pressure sensor are located within the brake pedal feel simulator, which is attached to the brake pedal assembly. Common causes include Faulty Brake Pedal Assembly, Brake Pedal Assembly harness is open or shorted, Brake Pedal Assembly circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1012 Ford indicates Brake Pedal Feel Simulator Cut-Off Valve Solenoid general Electrical Failure.
- Common causes
- Common causes include Faulty Brake Pedal Assembly, Brake Pedal Assembly harness is open or shorted, Brake Pedal Assembly circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1012 Ford Description
The ABS module will apply a Pulse Width Modulated (PWM) ground signal to the brake pedal feel simulator cut-off solenoid valve to increase the resistance felt when the driver applies the brake pedal.
The ABS module uses input from the brake pedal feel simulator cut-off valve pressure sensor to verify that the brake pedal feel simulator cut-off solenoid valve is functioning properly. If the ABS module detects a fault with a brake system component that would adversely affect brake-by-wire operation, the module will remove power from the brake pedal feel simulator cut-off valve solenoid, relieving simulator fluid pressure.
The ABS module provides the brake pedal feel simulator cut-off pressure sensor a 5-volt reference voltage. The brake pedal feel simulator provides a signal voltage proportional to the fluid pressure in the brake pedal feel simulator cut-off device to the ABS module. The ABS module provides a signal return for brake pedal feel simulator cut-off pressure sensor.
What are the Possible Causes of the DTC C1012 Ford?
- Faulty Brake Pedal Assembly
- Brake Pedal Assembly harness is open or shorted
- Brake Pedal Assembly circuit poor electrical connection
How to Fix the DTC C1012 Ford?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1012 Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1012 Ford code?
Need more information on how to fix the C1012 Ford code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1012 Ford code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1012 Ford Code
1. What does the OBDII code C1012 mean on a Ford vehicle?
The code C1012 indicates a general electrical failure in the Brake Pedal Feel Simulator Cut-Off Valve Solenoid.
2. What are the common symptoms of the C1012 code in a Ford?
Symptoms may include a brake warning light on the dashboard, reduced or inconsistent brake pedal feel, and possible loss of electronic brake assist.
3. What causes the C1012 code to appear?
Common causes include a faulty solenoid, damaged wiring or connectors, or an issue with the brake pedal feel simulator circuit.
4. Can I drive my Ford with the C1012 code active?
Driving with this code is not recommended, as it may affect brake performance and safety.
5. How can I diagnose the C1012 code?
Start by inspecting the wiring and connectors for damage or corrosion, then test the solenoid for proper operation using a multimeter.
6. How do you fix the C1012 code on a Ford?
Repairs may involve replacing the faulty solenoid, repairing damaged wiring, or clearing corroded connections.
7. Is the C1012 code related to other braking system issues?
Yes, it may be linked to problems with the ABS system or electronic brake assist functions.
8. Is this code specific to Ford vehicles?
While C1012 may appear on other vehicles, its definition and application to the Brake Pedal Feel Simulator Cut-Off Valve Solenoid are specific to Ford.
9. How much does it cost to repair the C1012 code?
Repair costs vary but typically range from $100 to $300, depending on whether the solenoid or wiring requires replacement.
10. Will clearing the C1012 code with a scanner fix the issue?
Clearing the code will not fix the problem; the underlying electrical failure must be addressed to prevent the code from returning.
Discuss the causes and fixes for C1012 Ford OBDII Code
Code C1012 Ford comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
