C1011 Ford Code - Brake Pedal Feel Simulator Cut-Off Pressure Sensor Signal Incorrect After Event
Quick Answer
The brake pedal feel simulator cut-off solenoid valve and brake pedal feel simulator cut-off pressure sensor are located within the brake pedal feel simulator, which is attached to the brake pedal assembly. Common causes include Faulty Brake Pedal Assembly, Brake Pedal Assembly harness is open or shorted, Brake Pedal Assembly circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1011 Ford indicates Brake Pedal Feel Simulator Cut-Off Pressure Sensor Signal Incorrect After Event.
- Common causes
- Common causes include Faulty Brake Pedal Assembly, Brake Pedal Assembly harness is open or shorted, Brake Pedal Assembly circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1011 Ford Description
The ABS module will apply a Pulse Width Modulated (PWM) ground signal to the brake pedal feel simulator cut-off solenoid valve to increase the resistance felt when the driver applies the brake pedal.
The ABS module uses input from the brake pedal feel simulator cut-off valve pressure sensor to verify that the brake pedal feel simulator cut-off solenoid valve is functioning properly. If the ABS module detects a fault with a brake system component that would adversely affect brake-by-wire operation, the module will remove power from the brake pedal feel simulator cut-off valve solenoid, relieving simulator fluid pressure.
The ABS module provides the brake pedal feel simulator cut-off pressure sensor a 5-volt reference voltage. The brake pedal feel simulator provides a signal voltage proportional to the fluid pressure in the brake pedal feel simulator cut-off device to the ABS module. The ABS module provides a signal return for brake pedal feel simulator cut-off pressure sensor.
What are the Possible Causes of the DTC C1011 Ford?
- Faulty Brake Pedal Assembly
- Brake Pedal Assembly harness is open or shorted
- Brake Pedal Assembly circuit poor electrical connection
How to Fix the DTC C1011 Ford?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
C1011:1F - Brake Pedal Feel Simulator Cut-Off Pressure Sensor: Circuit Intermittent
C1011:67 - Brake Pedal Feel Simulator Cut-Off Pressure Sensor: Signal Incorrect After Event
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1011 Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1011 Ford code?
Need more information on how to fix the C1011 Ford code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1011 Ford code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1011 Ford Code
1. What does the OBDII code C1011 mean on a Ford vehicle?
C1011 indicates an issue with the Brake Pedal Feel Simulator Cut-Off Pressure Sensor, where its signal is detected as incorrect after a specific event.
2. What are the common symptoms of code C1011 in Ford vehicles?
Symptoms include the ABS or brake warning light illuminating, reduced brake pedal feel, and potential issues with braking performance.
3. What causes the C1011 code to appear on a Ford?
Common causes include a faulty brake pedal feel simulator cut-off pressure sensor, damaged wiring or connectors, or failure of the ABS module.
4. Can I drive my Ford vehicle with the C1011 code?
While the vehicle may still be drivable, it is not recommended as braking performance could be compromised, posing a safety risk.
5. How is the C1011 code diagnosed on a Ford?
A technician will use a scan tool to read the ABS system, inspect the pressure sensor and its wiring, and test for proper voltage and signal output.
6. How do I fix the C1011 code on my Ford?
Repairs may include replacing the faulty pressure sensor, repairing damaged wiring or connectors, or reprogramming or replacing the ABS module.
7. Is the C1011 code covered under warranty for Ford vehicles?
It depends on your vehicle's warranty policy and coverage for the ABS system. Check with your dealer for details.
8. What tools are needed to troubleshoot the C1011 code?
A diagnostic scan tool compatible with Ford vehicles, a multimeter for checking wiring and voltage, and potentially a service manual for the vehicle.
9. How much does it cost to repair the C1011 code on a Ford?
Costs vary depending on the issue, but sensor replacement typically ranges from $150 to $300, while ABS module repairs or replacements can be significantly higher.
10. Can the C1011 code reset itself after repairs?
In some cases, the code may clear after the issue is resolved, but a scan tool may be needed to reset the ABS system and verify the fix.
Discuss the causes and fixes for C1011 Ford OBDII Code
Code C1011 Ford comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
