B2765 Jeep Code - Right C-Pillar Impact Acceleration Sensor
Quick Answer
The location of the right side impact sensor 2 is in the C-pillar area. Common causes include Faulty Right C-Pillar Impact Acceleration Sensor, Right C-Pillar Impact Acceleration Sensor harness is open or shorted, Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2765 Jeep indicates Right C-Pillar Impact Acceleration Sensor.
- Common causes
- Common causes include Faulty Right C-Pillar Impact Acceleration Sensor, Right C-Pillar Impact Acceleration Sensor harness is open or shorted, Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B2765 Jeep Description
This code will set, if the ORC and the Right Side Impact Sensor 2 do not establish and maintain valid data communications.
What are the Possible Causes of the DTC B2765 Jeep?
- Faulty Right C-Pillar Impact Acceleration Sensor
- Right C-Pillar Impact Acceleration Sensor harness is open or shorted
- Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection
- Faulty Occupant Restraint Controller (ORC)
How to Fix the DTC B2765 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B2765 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B2765 Jeep code?
Need more information on how to fix the B2765 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2765 Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B2765 Jeep Code
1. What does the OBDII code B2765 mean on a Jeep?
B2765 indicates a potential issue with the Right C-Pillar Impact Acceleration Sensor, which is part of the vehicle's airbag system.
2. What are the symptoms of code B2765 on a Jeep?
Common symptoms include an illuminated airbag warning light, a stored code in the airbag control module, or the airbag system being disabled.
3. What causes code B2765 to appear?
This code can be caused by a faulty Right C-Pillar Impact Acceleration Sensor, damaged wiring or connectors, or a malfunction in the airbag control module.
4. Is it safe to drive with code B2765 active?
No, it is not safe to drive, as the airbag system may not function correctly in the event of a collision.
5. How do you diagnose code B2765?
Diagnosis involves scanning the vehicle with an OBDII scanner, inspecting the sensor and its wiring for damage or corrosion, and testing the sensor's output with a multimeter.
6. Can the Right C-Pillar Impact Acceleration Sensor be repaired?
No, the sensor usually needs to be replaced if it is faulty. Repairs are typically limited to fixing damaged wiring or connectors.
7. How much does it cost to fix code B2765 on a Jeep?
Repair costs vary but typically range from $150 to $400, depending on whether the sensor, wiring, or both need replacement.
8. Can I clear code B2765 without fixing the issue?
You can clear the code with an OBDII scanner, but it will likely return unless the underlying issue is resolved.
9. What tools are needed to fix code B2765?
You may need an OBDII scanner, a multimeter, and basic hand tools for inspecting and replacing the sensor or repairing wiring.
10. Is a professional mechanic needed to fix code B2765?
While experienced DIYers may be able to fix it, professional service is recommended to ensure the airbag system functions correctly.
Discuss the causes and fixes for B2765 Jeep OBDII Code
Code B2765 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
