B2765 Dodge Code - Right C-Pillar Impact Acceleration Sensor
Quick Answer
The location of the right side impact sensor 2 is in the C-pillar area. Common causes include Faulty Right C-Pillar Impact Acceleration Sensor, Right C-Pillar Impact Acceleration Sensor harness is open or shorted, Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2765 Dodge indicates Right C-Pillar Impact Acceleration Sensor.
- Common causes
- Common causes include Faulty Right C-Pillar Impact Acceleration Sensor, Right C-Pillar Impact Acceleration Sensor harness is open or shorted, Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B2765 Dodge Description
This code will set, if the ORC and the Right Side Impact Sensor 2 do not establish and maintain valid data communications.
What are the Possible Causes of the DTC B2765 Dodge?
- Faulty Right C-Pillar Impact Acceleration Sensor
- Right C-Pillar Impact Acceleration Sensor harness is open or shorted
- Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection
- Faulty Occupant Restraint Controller (ORC)
How to Fix the DTC B2765 Dodge?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B2765 Dodge code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B2765 Dodge code?
Need more information on how to fix the B2765 Dodge code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2765 Dodge code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B2765 Dodge Code
1. What does the OBDII code B2765 on a Dodge mean?
The B2765 code indicates an issue with the right C-pillar impact acceleration sensor, which is part of the vehicle's airbag or crash detection system.
2. What are the symptoms of the B2765 code on a Dodge vehicle?
Common symptoms include the airbag warning light illuminating, potential deactivation of the airbag system, and error codes stored in the airbag control module.
3. What causes the B2765 code to appear?
This code can be caused by a faulty right C-pillar impact acceleration sensor, damaged wiring, poor electrical connections, or a malfunction in the airbag control module.
4. Is it safe to drive with the B2765 code active?
Driving is possible, but it’s not recommended as the airbag system may be compromised, potentially failing to deploy in the event of an accident.
5. How can I diagnose the B2765 code on a Dodge?
Use an OBDII scanner to confirm the code, then inspect the right C-pillar impact sensor, its wiring, and connectors for damage, corrosion, or loose connections.
6. Can a faulty impact sensor cause the airbag light to come on?
Yes, a malfunctioning right C-pillar impact acceleration sensor can trigger the airbag warning light.
7. How do I fix the B2765 code on my Dodge?
Repairs may include replacing the faulty sensor, repairing or replacing damaged wiring, cleaning corroded connectors, or resetting the airbag control module.
8. Where is the right C-pillar impact acceleration sensor located?
The sensor is typically located near the C-pillar on the right side of the vehicle, which is the area behind the rear passenger seat near the roof or side panel.
9. How much does it cost to repair the B2765 code?
Repair costs vary but can range from $150 to $400 depending on whether the sensor, wiring, or other components need replacement.
10. Do I need to clear the B2765 code after repairs?
Yes, after completing the necessary repairs, clear the code with an OBDII scanner and check if the airbag system functions correctly.
Discuss the causes and fixes for B2765 Dodge OBDII Code
Code B2765 Dodge comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
