AutoCodes – Dodge – B2762 Dodge

B2762 Dodge Code - Left C-Pillar Impact Acceleration Sensor

Quick Answer

The left side impact sensor 2 is located in the C-pillar area. Common causes include Faulty Left C-Pillar Impact Acceleration Sensor, Left C-Pillar Impact Acceleration Sensor harness is open or shorted, Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B2762 Dodge indicates Left C-Pillar Impact Acceleration Sensor.
Common causes: Common causes include Faulty Left C-Pillar Impact Acceleration Sensor, Left C-Pillar Impact Acceleration Sensor harness is open or shorted, Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 1,571

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jul 13, 2022

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B2762 Dodge Description

The left side impact sensor 2 is located in the C-pillar area. The impact sensors perform their own self-test using power supplied by the Occupant Restraint Controller (ORC) then communicates this status back to the ORC with periodic updates. The repair of this fault condition involves verifying the integrity of the wiring between the ORC and the sensor. The Occupant Restraint Controller (ORC) continuously communicates with the Left Side Impact Sensor 2 over the sensor signal circuit. The sensor communication and on board diagnostics are powered by the ORC signal.
This code will set, if the ORC and the Left Side Impact Sensor 2 do not establish and maintain valid data communications.

OBDII Code B2762 Dodge - Left C-Pillar Impact Acceleration Sensor - AutoCodes.com — B2762 Dodge Code - Left C-Pillar Impact Acceleration Sensor

What does this mean?

What are the Possible Causes of the DTC B2762 Dodge?

Faulty Left C-Pillar Impact Acceleration Sensor
Left C-Pillar Impact Acceleration Sensor harness is open or shorted
Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection
Faulty Occupant Restraint Controller (ORC)

How to Fix the DTC B2762 Dodge?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B2762 Dodge code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B2762 Dodge code?

Need more information on how to fix the B2762 Dodge code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B2762 Dodge code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B2762 Dodge Code

1. What are the common symptoms of OBDII code B2762 in a Dodge related to the Left C-Pillar Impact Acceleration Sensor?

The common symptoms include the airbag warning light illuminating on the dashboard, potential loss of functionality of the left side impact airbag, and diagnostic trouble code B2762 stored in the vehicle's system.

2. What could cause OBDII code B2762 to trigger in a Dodge?

The code B2762 is typically triggered in a Dodge due to a malfunction or failure of the Left C-Pillar Impact Acceleration Sensor, which is responsible for detecting impacts on the left side of the vehicle.

3. How can I diagnose the issue related to code B2762 in my Dodge?

Diagnosing the issue involves using a diagnostic scan tool to read the stored trouble codes, checking the wiring and connections related to the Left C-Pillar Impact Acceleration Sensor, and conducting a thorough inspection of the sensor itself for any visible damage.

4. Can I repair the Left C-Pillar Impact Acceleration Sensor in my Dodge myself?

While it is possible to replace the Left C-Pillar Impact Acceleration Sensor yourself, it is recommended to have the repair done by a professional technician to ensure proper installation and calibration of the new sensor.

5. Are there any safety concerns associated with OBDII code B2762 in a Dodge?

Yes, there are safety concerns as the malfunction of the Left C-Pillar Impact Acceleration Sensor can affect the proper deployment of the left side impact airbag in the event of a collision, potentially compromising the safety of the vehicle occupants.

6. Is it safe to drive my Dodge with OBDII code B2762 present?

It is not advisable to drive the vehicle with code B2762 present, as the left side impact airbag may not deploy correctly in the event of a collision, putting the occupants at risk of injury.

7. How much does it typically cost to repair OBDII code B2762 in a Dodge?

The cost of repairing OBDII code B2762 in a Dodge can vary depending on the extent of the damage and whether the sensor needs to be replaced. It is recommended to get a professional assessment for an accurate estimate.

8. Can resetting the trouble codes clear OBDII code B2762 in a Dodge?

Resetting the trouble codes may temporarily clear the code, but if the underlying issue with the Left C-Pillar Impact Acceleration Sensor is not addressed, the code is likely to reappear.

9. Are there any recalls or technical service bulletins related to OBDII code B2762 in Dodge vehicles?

It is advisable to check with the manufacturer or a Dodge dealership to inquire about any recalls or technical service bulletins related to OBDII code B2762 and the Left C-Pillar Impact Acceleration Sensor for your specific vehicle model.

10. Can a faulty Left C-Pillar Impact Acceleration Sensor affect other safety systems in my Dodge?

Yes, a faulty sensor can potentially affect other safety systems that rely on its input, such as the overall airbag system and the vehicle's safety restraint system, highlighting the importance of addressing the issue promptly.