B2210 RAM Code - Occupant Restraint Controller Control Driver 2
Quick Answer
When powered, the Occupant Restraint Controller (ORC) performs an internal self test. Common causes include Faulty Occupant Restraint Controller (ORC), Occupant Restraint Controller (ORC) harness is open or shorted, Occupant Restraint Controller (ORC) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2210 RAM indicates Occupant Restraint Controller Control Driver 2.
- Common causes
- Common causes include Faulty Occupant Restraint Controller (ORC), Occupant Restraint Controller (ORC) harness is open or shorted, Occupant Restraint Controller (ORC) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B2210 RAM Description
What are the Possible Causes of the DTC B2210 RAM?
- Faulty Occupant Restraint Controller (ORC)
- Occupant Restraint Controller (ORC) harness is open or shorted
- Occupant Restraint Controller (ORC) circuit poor electrical connection
How to Fix the DTC B2210 RAM?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B2210 RAM code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B2210 RAM code?
Need more information on how to fix the B2210 RAM code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2210 RAM code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B2210 RAM Code
1. What does the OBDII code B2210 RAM mean?
Code B2210 indicates an issue with the Occupant Restraint Controller (ORC), specifically related to the Control Driver 2 circuit, often tied to the airbag system.
2. What are the common symptoms of the B2210 code?
Symptoms may include an illuminated airbag warning light, malfunctioning airbags, or fault codes stored in the ORC module.
3. What causes the B2210 code to appear?
Common causes include a faulty Occupant Restraint Controller, damaged wiring or connectors in the airbag system, or a malfunctioning airbag component.
4. Is it safe to drive with the B2210 code active?
It is not safe to drive with this code active as it may indicate a malfunction in the airbag system, potentially leaving the airbags inoperable during a collision.
5. How can you diagnose the B2210 code?
Use a diagnostic scanner to read trouble codes, inspect the wiring and connectors for damage, and test the ORC for proper functionality.
6. Can a loose connector cause the B2210 code?
Yes, a loose or corroded connector in the airbag system can trigger the B2210 code by disrupting the signal to the ORC.
7. How do you fix the B2210 code?
Repairs may include replacing or repairing damaged wiring, securing loose connectors, or replacing the faulty Occupant Restraint Controller.
8. How much does it cost to fix the B2210 code?
Repair costs vary, ranging from $50 for minor wiring repairs to $1,000 or more if the ORC or airbag components need replacement.
9. Can a software update resolve the B2210 code?
In some cases, a software update for the ORC module may resolve the issue, but this depends on the vehicle and specific circumstances.
10. Should the airbag system be recalibrated after fixing the B2210 code?
Yes, after repairs, the airbag system should be recalibrated and tested to ensure proper functionality and safety compliance.
Discuss the causes and fixes for B2210 RAM OBDII Code
Code B2210 RAM comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
