B1941 Scion Code - Open in Selectable Force Limiter Squib Right Circuit
Quick Answer
The Selectable Force Limiter Squib Right (RH) Circuit consists of the Center Airbag Sensor Assembly and Front Seat Outer Belt Assembly Right (RH). Common causes include Faulty Front Seat Outer Belt Assembly Right (RH) (Selectable Force Limiter Squib Right), Front Seat Outer Belt Assembly Right harness is open or shorted, Front Seat Outer Belt Assembly Right circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1941 Scion indicates Open in Selectable Force Limiter Squib Right Circuit.
- Common causes
- Common causes include Faulty Front Seat Outer Belt Assembly Right (RH) (Selectable Force Limiter Squib Right), Front Seat Outer Belt Assembly Right harness is open or shorted, Front Seat Outer Belt Assembly Right circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1941 Scion Description
What are the Possible Causes of the DTC B1941 Scion?
- Faulty Front Seat Outer Belt Assembly Right (RH) (Selectable Force Limiter Squib Right)
- Front Seat Outer Belt Assembly Right harness is open or shorted
- Front Seat Outer Belt Assembly Right circuit poor electrical connection
- Faulty Center Airbag Sensor Assembly
How to Fix the DTC B1941 Scion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1941 Scion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1941 Scion code?
Need more information on how to fix the B1941 Scion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1941 Scion code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1941 Scion Code
What does the OBDII code B1941 mean for a Scion?
B1941 indicates an open circuit in the selectable force limiter squib (right side) of the airbag system, which may affect proper airbag deployment.
What are the common symptoms of code B1941 in a Scion?
The most common symptom is the illumination of the airbag warning light on the dashboard.
What causes the B1941 code in a Scion?
This code is typically caused by a damaged or disconnected wiring harness, a faulty clock spring, a defective airbag module, or corrosion at electrical connectors.
Can I drive my Scion with the B1941 code active?
While the vehicle may still drive, the airbag system might not function properly in an accident, posing a safety risk. It’s recommended to address the issue promptly.
How is the B1941 code diagnosed on a Scion?
A mechanic will use an OBDII scanner to retrieve the code, inspect the airbag system wiring, connectors, and clock spring, and perform continuity tests to identify the fault.
What should I check first when troubleshooting code B1941?
Start by inspecting the wiring and connectors for the selectable force limiter squib on the right side for visible damage, disconnections, or corrosion.
How do I fix the B1941 code on my Scion?
Repairs may include reconnecting or replacing damaged wires, cleaning corroded connectors, replacing a faulty clock spring, or replacing the airbag module if necessary.
What tools are needed to repair the B1941 code?
You’ll typically need an OBDII scanner, a multimeter, and possibly specialty tools for accessing and replacing airbag system components.
Is the B1941 code covered under warranty for a Scion?
Airbag system issues may be covered under the vehicle's warranty or a recall, so check with your dealership or manufacturer for details.
How much does it cost to fix code B1941 on a Scion?
Repair costs can range from $100 to $1,000 depending on the specific issue, such as wiring repairs or replacing components like the clock spring or airbag module.
Discuss the causes and fixes for B1941 Scion OBDII Code
Code B1941 Scion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
