AutoCodes – Ford – B1407 Ford

B1407 Ford Code - Passenger Side Airbag Deployment Control Circuit

Quick Answer

The Restraint Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. Common causes include Faulty Passenger Side Airbag, Passenger Side Airbag harness is open or shorted, Passenger Side Airbag circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B1407 Ford indicates Passenger Side Airbag Deployment Control Circuit.
Common causes: Common causes include Faulty Passenger Side Airbag, Passenger Side Airbag harness is open or shorted, Passenger Side Airbag circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 22,785

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Apr 04, 2019

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B1407 Ford Description

The Restraint Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. The value displayed in the PID is the deployment loop resistance measured by the RCM. If the value displayed is lower or higher than the desired range, the RCM can set a Diagnostic Trouble Code (DTC). As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. Small variations in resistance can occur due to the effect of road vibrations on terminal fit. Crimps and terminals can be affected by stress and harness movement and can cause an increase in resistance due to wire strain. These variables can result in an intermittent fault. For this reason, the test requires the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at the time of diagnosis. Following this direction helps make sure that minor changes in resistance do not create a repeat concern.

OBDII Code B1407 Ford - Passenger Side Airbag Deployment Control Circuit - AutoCodes.com — B1407 Ford Code - Passenger Side Airbag Deployment Control Circuit

What does this mean?

What are the Possible Causes of the DTC B1407 Ford?

Faulty Passenger Side Airbag
Passenger Side Airbag harness is open or shorted
Passenger Side Airbag circuit poor electrical connection
Faulty Restraint Control Module (RCM)

How to Fix the DTC B1407 Ford?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B1407:11 Passenger Side Airbag Deployment Control Circuit Short to Ground
B1407:12 Passenger Side Airbag Deployment Control Circuit Short to Battery
B1407:13 Passenger Side Airbag Deployment Control Circuit Open
B1407:1A Passenger Side Airbag Deployment Control Circuit Resistance Below Threshold

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1407 Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B1407 Ford code?

Need more information on how to fix the B1407 Ford code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1407 Ford code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1407 Ford Code

1. What are the common symptoms of OBDII code B1407 in a Ford related to the passenger side airbag deployment control circuit?

The common symptoms include the airbag warning light illuminating on the dashboard, potential non-deployment of the passenger side airbag in a collision, and diagnostic trouble codes stored in the vehicle's computer.

2. What are some possible causes of OBDII code B1407 Ford related to the passenger side airbag deployment control circuit?

Possible causes include faulty wiring or connectors in the airbag system, a defective passenger side airbag deployment control module, or issues with the airbag sensor itself.

3. How can I diagnose the OBDII code B1407 in my Ford vehicle?

Diagnosing OBDII code B1407 typically involves using a diagnostic scanner to retrieve the specific fault code, checking the wiring and connectors in the passenger side airbag system, and testing the components for proper functionality.

4. Is it safe to drive my Ford with OBDII code B1407 related to the passenger side airbag deployment control circuit?

It is not recommended to drive the vehicle with an active airbag fault code, as it may compromise the safety features of the airbag system. It is advisable to have the issue diagnosed and repaired as soon as possible.

5. Can I reset the OBDII code B1407 in my Ford without fixing the underlying issue?

While you can clear the fault code using a diagnostic scanner, the underlying issue causing the code will persist. It is important to address the root cause of the problem to ensure the proper functioning of the passenger side airbag system.

6. How much does it typically cost to repair OBDII code B1407 in a Ford related to the passenger side airbag deployment control circuit?

The cost of repairing OBDII code B1407 can vary depending on the specific cause of the issue and the labor rates of the repair shop. It is advisable to obtain quotes from different mechanics or dealerships for an accurate estimate.

7. Are there any common DIY repair tips for addressing OBDII code B1407 in a Ford?

DIY repair for OBDII code B1407 can be challenging due to the safety concerns associated with the airbag system. It is recommended to have the issue diagnosed and repaired by a qualified technician to ensure proper safety measures are followed.

8. How long does it typically take to repair OBDII code B1407 related to the passenger side airbag deployment control circuit in a Ford?

The repair time for OBDII code B1407 can vary depending on the complexity of the issue and the availability of parts. In some cases, the repair may be completed within a few hours, while more complex issues may require additional time.

9. Can OBDII code B1407 in a Ford be a recurring issue even after repair?

If the underlying cause of OBDII code B1407 is not properly addressed during the repair, it is possible for the issue to recur. It is important to ensure that all components related to the passenger side airbag system are thoroughly inspected and any faulty parts are replaced.

10. Is it necessary to have the OBDII code B1407 cleared by a professional after the repair is completed?

Once the underlying issue causing OBDII code B1407 is fixed, the fault code should be cleared using a diagnostic scanner. This can be done by a professional technician or by using a scanner if you are familiar with the process.