B1150 Scion Code - Occupant Classification System Malfunction
Quick Answer
The occupant classification system circuit consists of the Airbag Sensor Assembly Center and the occupant classification system. Common causes include Faulty Occupant classification system, Faulty Airbag Sensor Assembly Center, Right front seat wire. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1150 Scion indicates Occupant Classification System Malfunction.
- Common causes
- Common causes include Faulty Occupant classification system, Faulty Airbag Sensor Assembly Center, Right front seat wire.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1150 Scion Description
What are the Possible Causes of the DTC B1150 Scion?
- Faulty Occupant classification system
- Faulty Airbag Sensor Assembly Center
- Right front seat wire
How to Fix the DTC B1150 Scion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1150 Scion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1150 Scion code?
Need more information on how to fix the B1150 Scion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1150 Scion code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1150 Scion Code
1. What are the common symptoms of OBDII code B1150 in a Scion related to the Occupant Classification System Malfunction?
The common symptoms include the airbag warning light staying illuminated, the passenger airbag being disabled, and potential issues with the seat belt warning system.
2. What causes the OBDII code B1150 to occur in a Scion's Occupant Classification System?
The code B1150 is typically triggered by a malfunction in the occupant classification system module, faulty seat weight sensors, damaged wiring, or a disconnected electrical connector.
3. How can I diagnose the OBDII code B1150 in my Scion related to the Occupant Classification System Malfunction?
Diagnosing the code involves using a professional OBDII scanner to retrieve the specific fault code, conducting a visual inspection of the seat sensors and wiring, and performing system tests to pinpoint the exact issue.
4. Can I still drive my Scion with the OBDII code B1150 related to the Occupant Classification System Malfunction?
It is not recommended to drive the vehicle with the B1150 code active, as it can affect the proper functioning of the airbag system and compromise passenger safety in the event of a collision.
5. How can I reset the OBDII code B1150 in my Scion after repairing the Occupant Classification System issue?
After resolving the underlying issue causing the B1150 code, you can reset it using an OBDII scanner by clearing the diagnostic trouble codes in the system.
6. Are there any DIY repair tips for fixing the OBDII code B1150 in a Scion related to the Occupant Classification System Malfunction?
DIY repair tips include checking and securing the electrical connectors, inspecting and cleaning the seat sensors, and ensuring all wiring is intact and properly connected.
7. Is it safe to attempt repairs on the Occupant Classification System related to the OBDII code B1150 in a Scion myself?
While some DIY repairs can be done, it is recommended to consult a professional mechanic or dealership with experience in airbag systems to ensure proper diagnosis and repair of the issue.
8. How much does it typically cost to repair the OBDII code B1150 in a Scion's Occupant Classification System?
The cost of repairs can vary depending on the exact cause of the issue, but it may range from a few hundred to over a thousand dollars, including parts and labor.
9. Can the OBDII code B1150 in a Scion be caused by a faulty airbag module?
While it is less common, a faulty airbag module can potentially trigger the B1150 code if it is not communicating properly with the occupant classification system module.
10. Will the OBDII code B1150 in a Scion reset on its own after the issue is fixed?
In some cases, the B1150 code may reset on its own after the underlying problem is resolved, but it is recommended to use an OBDII scanner to clear the code manually for safe measure.
Discuss the causes and fixes for B1150 Scion OBDII Code
Code B1150 Scion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
