AutoCodes – Lincoln – B0072 Lincoln

B0072 Lincoln Code - Passenger Seatbelt Pretensioner 'A' Deployment Control

Quick Answer

The Restraints Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. Common causes include Faulty Passenger Seatbelt Pretensioner, Passenger Seatbelt Pretensioner harness is open or shorted, Passenger Seatbelt Pretensioner circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B0072 Lincoln indicates Passenger Seatbelt Pretensioner 'A' Deployment Control.
Common causes: Common causes include Faulty Passenger Seatbelt Pretensioner, Passenger Seatbelt Pretensioner harness is open or shorted, Passenger Seatbelt Pretensioner circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 2,352

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jun 14, 2020

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B0072 Lincoln Description

The Restraints Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. The value displayed in the PID is the deployment loop resistance measured by the RCM. If the value displayed is lower or higher than the desired range, the RCM can set a Diagnostic Trouble Code (DTC). As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. Small variations in resistance can occur due to the effect of road vibrations on terminal fit. Crimps and terminals can be affected by stress and harness movement and can cause an increase in resistance due to wire strain. These variables can result in an intermittent fault. For this reason, the test requires the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at the time of diagnosis. Following this direction helps make sure that minor changes in resistance do not create a repeat concern. This test uses the process of elimination to diagnose each part of the deployment loop circuit including:
- Wiring
- Connections
- Driver seatbelt anchor pretensioner
- RCM

OBDII Code B0072 Lincoln - Passenger Seatbelt Pretensioner 'A' Deployment Control - AutoCodes.com — B0072 Lincoln Code - Passenger Seatbelt Pretensioner 'A' Deployment Control

What does this mean?

What are the Possible Causes of the DTC B0072 Lincoln?

Faulty Passenger Seatbelt Pretensioner
Passenger Seatbelt Pretensioner harness is open or shorted
Passenger Seatbelt Pretensioner circuit poor electrical connection
Faulty Restraints Control Module (RCM)

How to Fix the DTC B0072 Lincoln?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B0072:11 Passenger Seatbelt Pretensioner 'A' Deployment Control: Circuit Short to Ground
B0072:12 Passenger Seatbelt Pretensioner 'A' Deployment Control: Circuit Short to Battery
B0072:13 Passenger Seatbelt Pretensioner 'A' Deployment Control: Circuit Open
B0072:1A Passenger Seatbelt Pretensioner 'A' Deployment Control: Circuit Resistance Below Threshold

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B0072 Lincoln code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B0072 Lincoln code?

Need more information on how to fix the B0072 Lincoln code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B0072 Lincoln code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B0072 Lincoln Code

1. What does OBDII code B0072 for Lincoln mean?

The B0072 code specifically refers to an issue with the Passenger Seatbelt Pretensioner 'A' Deployment Control in a Lincoln vehicle.

2. What are the common symptoms of OBDII code B0072 in a Lincoln?

Common symptoms of code B0072 may include the airbag warning light illuminating on the dashboard and potential issues with the passenger seatbelt pretensioner.

3. What are possible causes of OBDII code B0072 in a Lincoln?

Potential causes of code B0072 can include a faulty passenger seatbelt pretensioner, damaged wiring or connectors in the seatbelt system, or a malfunction in the deployment control module.

4. How serious is OBDII code B0072 in a Lincoln?

Code B0072 should be taken seriously as it indicates a problem with the passenger seatbelt pretensioner, a crucial safety component in the event of a collision.

5. Can I continue driving my Lincoln with OBDII code B0072?

It is not recommended to continue driving a vehicle with an active B0072 code, as it may compromise the effectiveness of the passenger seatbelt pretensioner in an accident.

6. How can I diagnose OBDII code B0072 in my Lincoln?

Diagnosing code B0072 typically involves using a diagnostic scanner to retrieve the specific code, followed by inspecting the passenger seatbelt system and related components for any visible damage or issues.

7. How can I repair OBDII code B0072 in my Lincoln?

Repairing code B0072 may involve replacing the faulty passenger seatbelt pretensioner, repairing or replacing damaged wiring, or addressing any issues with the deployment control module as necessary.

8. Can resetting the OBDII system clear code B0072 in a Lincoln?

Resetting the OBDII system may temporarily clear the code, but it is important to address the underlying issue causing code B0072 to prevent it from returning.

9. Is it possible to prevent OBDII code B0072 in a Lincoln?

While some causes of code B0072 may be due to wear and tear, regular maintenance of the seatbelt system and addressing any warning signs promptly can help prevent this code from appearing.

10. Should I seek professional help for OBDII code B0072 in my Lincoln?

Given the importance of the seatbelt pretensioner for safety, it is recommended to seek assistance from a qualified technician to properly diagnose and repair code B0072 in your Lincoln.