AutoCodes – GMC – B0014 2018 GMC Sierra

B0014 2018 GMC Sierra Code - Driver Seat Side Air Bag Deployment Loop

Quick Answer

During a side or frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current flow through the deployment loop in order to deploy the side impact module. Common causes include Faulty Driver Seat Side Air Bag, Driver Seat Side Air Bag harness is open or shorted, Driver Seat Side Air Bag circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B0014 2018 GMC Sierra indicates Driver Seat Side Air Bag Deployment Loop.
Common causes: Common causes include Faulty Driver Seat Side Air Bag, Driver Seat Side Air Bag harness is open or shorted, Driver Seat Side Air Bag circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 440

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Oct 09, 2022

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B0014 2018 GMC Sierra Description

During a side or frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current flow through the deployment loop in order to deploy the side impact module. A shorting bar is located in the electrical connector of the side impact module. The side impact module high control circuit and low control circuit are shorted together by the shorting bar when the electrical connector is disconnected. The shorting bar helps prevent unwanted deployment of the inflator module during servicing. The SDM performs a continuous diagnostic test on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If the results of any deployment loop circuit test are below specifications the code B0014 and the appropriate symptom byte will be set.

OBDII Code B0014 2018 GMC Sierra - Driver Seat Side Air Bag Deployment Loop - AutoCodes.com — B0014 2018 GMC Sierra Code - Driver Seat Side Air Bag Deployment Loop

What does this mean?

What are the Possible Causes of the DTC B0014 2018 GMC Sierra?

Faulty Driver Seat Side Air Bag
Driver Seat Side Air Bag harness is open or shorted
Driver Seat Side Air Bag circuit poor electrical connection
Faulty Sensing and Diagnostic Module (SDM)

How to Fix the DTC B0014 2018 GMC Sierra?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B0014:01 Driver Seat Side Air Bag Deployment Loop Short to Battery
B0014:02 Driver Seat Side Air Bag Deployment Loop Short to Ground
B0014:04 Driver Seat Side Air Bag Deployment Loop Open
B0014:0D Driver Seat Side Air Bag Deployment Loop High Resistance
B0014:0E Driver Seat Side Air Bag Deployment Loop Low Resistance

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B0014 2018 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B0014 2018 GMC Sierra code?

Need more information on how to fix the B0014 2018 GMC Sierra code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B0014 2018 GMC Sierra code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B0014 2018 GMC Sierra Code

1. What are common symptoms of OBDII code B0014 in a 2018 GMC Sierra related to the driver seat side airbag deployment loop?

- The most common symptoms include the airbag warning light illuminating on the dashboard and a potential message indicating a fault with the driver seat side airbag system.

2. What are the possible causes of OBDII code B0014 in a 2018 GMC Sierra?

- The code B0014 typically indicates an open or high resistance condition in the driver seat side airbag deployment loop, which can be caused by a faulty airbag sensor, damaged wiring, or a malfunctioning airbag module.

3. How can I diagnose the issue causing OBDII code B0014 in my 2018 GMC Sierra?

- To diagnose the problem, you can use a diagnostic scanner to retrieve the specific trouble code, inspect the wiring and connections related to the driver seat side airbag system, and test the airbag sensor and module for proper functionality.

4. Is it safe to drive my 2018 GMC Sierra with OBDII code B0014 related to the driver seat side airbag deployment loop?

- It is not recommended to drive the vehicle with an active airbag system fault code, as it may compromise the effectiveness of the driver seat side airbag in the event of a collision.

5. Can I reset OBDII code B0014 in my 2018 GMC Sierra without fixing the underlying issue?

- While you can clear the code temporarily, it will likely reappear until the root cause of the problem is addressed. It is essential to diagnose and repair the issue to ensure the proper functioning of the driver seat side airbag system.

6. What are some repair tips for fixing OBDII code B0014 in a 2018 GMC Sierra?

- Repair tips include checking and repairing any damaged wiring, replacing the faulty airbag sensor or module if necessary, and ensuring all connections are secure and free of corrosion.

7. How much does it typically cost to repair OBDII code B0014 in a 2018 GMC Sierra?

- The cost of repairing OBDII code B0014 can vary depending on the specific cause of the issue, but it may involve expenses for parts, labor, and diagnostic services. It is recommended to consult a professional mechanic for an accurate estimate.

8. Can I fix OBDII code B0014 in my 2018 GMC Sierra by myself, or do I need to take it to a mechanic?

- While some DIY enthusiasts may be able to diagnose and repair simple issues related to OBDII code B0014, it is recommended to seek the expertise of a qualified mechanic, especially when dealing with airbag systems due to safety concerns.

9. Are there any recalls or technical service bulletins related to OBDII code B0014 in a 2018 GMC Sierra?

- It is advisable to check with GMC or a certified dealership to inquire about any recalls or technical service bulletins concerning OBDII code B0014 in the 2018 Sierra, as manufacturers sometimes provide solutions for common issues.

10. Can unresolved OBDII code B0014 in a 2018 GMC Sierra affect the vehicle's overall safety?

- Yes, leaving OBDII code B0014 unaddressed can potentially compromise the driver's safety in the event of an accident by impairing the functionality of the driver seat side airbag system. It is crucial to promptly diagnose and repair such issues to ensure the vehicle's safety systems are in proper working condition.