C1440 Mercury Code - Pressure Transducer Main/Primary Signal Faulted
Quick Answer
The pressure transducer is integral to the Hydraulic Control Unit (HCU). Common causes include Faulty Hydraulic Control Unit (HCU), Hydraulic Control Unit (HCU) harness is open or shorted, Hydraulic Control Unit (HCU) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1440 Mercury indicates Pressure Transducer Main/Primary Signal Faulted.
- Common causes
- Common causes include Faulty Hydraulic Control Unit (HCU), Hydraulic Control Unit (HCU) harness is open or shorted, Hydraulic Control Unit (HCU) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1440 Mercury Description
When the brake pedal is pressed, the stop lamp switch closes and a voltage is sent to the Powertrain Control Module (PCM). The PCM then sends a message over the High-Speed Controller Area Network (HS-CAN) to the ABS module indicating that the brake pedal has been pressed. DTCs set in the ignition cycle can only be cleared by cycling the ignition off and on once the fault has been corrected.
This DTC sets in every ignition cycle if the signal that the pressure transducer sends to the ABS module does not agree with the stop lamp switch position.
What are the Possible Causes of the DTC C1440 Mercury?
- Faulty Hydraulic Control Unit (HCU)
- Hydraulic Control Unit (HCU) harness is open or shorted
- Hydraulic Control Unit (HCU) circuit poor electrical connection
How to Fix the DTC C1440 Mercury?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1440 Mercury code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1440 Mercury code?
Need more information on how to fix the C1440 Mercury code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1440 Mercury code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1440 Mercury Code
1. What are the common symptoms of OBDII code C1440 in a Mercury vehicle?
- The common symptoms of code C1440 include the ABS warning light illuminating on the dashboard, potential loss of ABS functionality, and potential issues with the vehicle's braking system.
2. What can cause the OBDII code C1440 in a Mercury car?
- The code C1440 in a Mercury vehicle is typically caused by a fault in the pressure transducer, which is responsible for monitoring the hydraulic pressure in the braking system.
3. How serious is OBDII code C1440 in a Mercury car?
- Code C1440 should be taken seriously as it can affect the proper functioning of the vehicle's ABS system, potentially compromising braking performance and overall safety.
4. Can I continue driving my Mercury with OBDII code C1440?
- It is not recommended to drive your Mercury with code C1440, as it can lead to safety issues due to potential ABS system malfunctions. It's best to address the issue promptly.
5. How can I diagnose and repair OBDII code C1440 in my Mercury?
- Diagnosis of code C1440 involves using a diagnostic scanner to retrieve the specific fault codes and then testing the pressure transducer for proper operation. Repair typically involves replacing the faulty pressure transducer.
6. Is it possible to reset OBDII code C1440 in a Mercury without fixing the issue?
- While you can clear the code temporarily by resetting the vehicle's ECU, the underlying issue causing code C1440 will persist until it is properly diagnosed and repaired.
7. Are there any DIY tips for addressing OBDII code C1440 in a Mercury?
- DIY tips for addressing code C1440 include checking the wiring and connections to the pressure transducer for any visible damage or corrosion before considering a replacement.
8. How much does it cost to repair OBDII code C1440 in a Mercury?
- The cost of repairing code C1440 in a Mercury can vary depending on the model, labor rates, and whether you choose to address the issue yourself or take it to a professional mechanic.
9. Will OBDII code C1440 cause my Mercury to fail an emissions test?
- While code C1440 is related to the ABS system and not emissions, it's essential to address the issue to ensure your vehicle is in proper working condition for overall safety and performance.
10. Can a faulty pressure transducer lead to other issues in my Mercury besides triggering code C1440?
- A faulty pressure transducer can lead to ABS system malfunctions, affecting braking performance and potentially compromising overall vehicle safety. It's crucial to address the issue promptly.
Discuss the causes and fixes for C1440 Mercury OBDII Code
Code C1440 Mercury comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
