C1336 2014 Toyota RAV4 Code - Zero Point Calibration of Acceleration Sensor Undone
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) receives signals from the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) via the Controller Area Network (CAN) communication system. Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly). Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1336 2014 Toyota RAV4 indicates Zero Point Calibration of Acceleration Sensor Undone.
- Common causes
- Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly).
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1336 2014 Toyota RAV4 Description
The Airbag Sensor Assembly has a built-in Yaw Rate Sensor and Acceleration Sensor and detects the vehicle's condition. If there is trouble in the bus lines between the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.
The Diagnostic Trouble Code (DTC) is also output when the calibration has not been completed.
What are the Possible Causes of the DTC C1336 2014 Toyota RAV4?
- Acceleration Sensor Calibration
- Sensor installation
- Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly)
- Airbag Sensor Assembly harness is open or shorted
- Airbag Sensor Assembly circuit poor electrical connection
- Faulty Skid Control ECU (Brake Actuator Assembly)
How to Fix the DTC C1336 2014 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1336 2014 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1336 2014 Toyota RAV4 code?
Need more information on how to fix the C1336 2014 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1336 2014 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1336 2014 Toyota RAV4 Code
1. What does the OBDII code C1336 in a 2014 Toyota RAV4 indicate?
The code C1336 signifies that the zero point calibration of the acceleration sensor is undone in the vehicle.
2. What are the common symptoms associated with the C1336 code in a 2014 Toyota RAV4?
Common symptoms include the vehicle's traction control light being illuminated on the dashboard and potential issues with the vehicle's stability control system.
3. What are the possible causes of the C1336 code in a 2014 Toyota RAV4?
The C1336 code can be triggered by a misalignment of the yaw rate sensor or acceleration sensor, damaged wiring in the sensor circuit, or a faulty sensor.
4. How can I diagnose the C1336 code in my 2014 Toyota RAV4?
Diagnosing the C1336 code typically involves conducting a visual inspection of the sensor components, checking the sensor connections for any damage, and performing a zero point calibration using a diagnostic scanner.
5. Can I drive my 2014 Toyota RAV4 with the C1336 code?
While it may be possible to drive the vehicle with the C1336 code, it is recommended to address the issue promptly to ensure the proper functioning of the vehicle's stability control system.
6. How can the C1336 code in a 2014 Toyota RAV4 be repaired?
Repairing the C1336 code often involves performing a zero point calibration of the acceleration sensor using a diagnostic scanner and ensuring that all sensor components are properly aligned and functioning correctly.
7. Is the repair for the C1336 code in a 2014 Toyota RAV4 something I can do myself?
Performing a zero point calibration for the C1336 code may require specialized diagnostic equipment, so it is recommended to have the repair done by a qualified mechanic or dealership.
8. Are there any recalls related to the C1336 code in a 2014 Toyota RAV4?
Recalls related to the C1336 code may vary by region and vehicle production date, so it is advisable to check with your local Toyota dealership or visit the manufacturer's website for any relevant recall information.
9. How much does it typically cost to repair the C1336 code in a 2014 Toyota RAV4?
The cost of repairing the C1336 code can vary depending on the extent of the issue, the labor rates of the repair shop, and whether any sensor components need to be replaced. It is recommended to obtain quotes from different repair facilities for an accurate estimate.
10. Can the C1336 code in a 2014 Toyota RAV4 cause any other problems if left unaddressed?
Leaving the C1336 code unresolved can potentially lead to issues with the vehicle's stability control system, traction control, and overall handling, so it is advisable to address the problem promptly.
Discuss the causes and fixes for C1336 2014 Toyota RAV4 OBDII Code
Code C1336 2014 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
