C1336 2013 Toyota RAV4 Code - Zero Point Calibration of Acceleration Sensor Undone
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) receives signals from the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) via the Controller Area Network (CAN) communication system. Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly). Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1336 2013 Toyota RAV4 indicates Zero Point Calibration of Acceleration Sensor Undone.
- Common causes
- Common causes include Acceleration Sensor Calibration, Sensor installation, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly).
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1336 2013 Toyota RAV4 Description
The Airbag Sensor Assembly has a built-in Yaw Rate Sensor and Acceleration Sensor and detects the vehicle's condition. If there is trouble in the bus lines between the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.
The Diagnostic Trouble Code (DTC) is also output when the calibration has not been completed.
What are the Possible Causes of the DTC C1336 2013 Toyota RAV4?
- Acceleration Sensor Calibration
- Sensor installation
- Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly)
- Airbag Sensor Assembly harness is open or shorted
- Airbag Sensor Assembly circuit poor electrical connection
- Faulty Skid Control ECU (Brake Actuator Assembly)
How to Fix the DTC C1336 2013 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1336 2013 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1336 2013 Toyota RAV4 code?
Need more information on how to fix the C1336 2013 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1336 2013 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1336 2013 Toyota RAV4 Code
1. What does the OBDII code C1336 mean on a 2013 Toyota RAV4?
C1336 indicates that the Zero Point Calibration of the acceleration sensor is undone or incomplete, which can affect the functionality of systems like ABS and traction control.
2. What are the common symptoms of the C1336 code in a Toyota RAV4?
Common symptoms include the ABS or traction control warning lights being illuminated and potential loss of stability control system functionality.
3. What causes the C1336 code to appear in a 2013 Toyota RAV4?
The code is often triggered after battery disconnection, sensor replacement, or repairs involving the steering, suspension, or alignment that require recalibration.
4. Can I drive my 2013 Toyota RAV4 with the C1336 code active?
While the vehicle may still be drivable, safety features like ABS and traction control may not work properly, increasing the risk of an accident in certain conditions.
5. How is the C1336 code fixed on a 2013 Toyota RAV4?
The issue is resolved by performing a Zero Point Calibration using a scan tool or diagnostic equipment to recalibrate the acceleration sensor.
6. What tools are needed to perform Zero Point Calibration for C1336 on a Toyota RAV4?
A compatible OBDII scan tool or Toyota Techstream software is required to perform the Zero Point Calibration procedure.
7. Can I perform Zero Point Calibration for C1336 without professional help?
If you have access to the proper scan tool and follow the specific instructions for your vehicle, you can perform the calibration yourself. However, professional help is recommended if you're unsure.
8. Does a wheel alignment affect the C1336 code on a 2013 Toyota RAV4?
Yes, a wheel alignment or suspension repairs can trigger the C1336 code if Zero Point Calibration is not performed afterward.
9. How long does it take to fix the C1336 code on a 2013 Toyota RAV4?
Performing Zero Point Calibration typically takes 15-30 minutes with the correct tools and instructions.
10. Can a low or disconnected battery cause the C1336 code to appear?
Yes, disconnecting or replacing the battery can erase the Zero Point Calibration data, leading to the C1336 code.
Discuss the causes and fixes for C1336 2013 Toyota RAV4 OBDII Code
Code C1336 2013 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
