C1290 2014 Toyota RAV4 Code - Steering Angle Sensor Zero Point Malfunction
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) acquires steering sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. Common causes include Yaw rate and deceleration sensor zero point calibration incomplete, Poor adjustment of centered position of the steering wheel, Poor adjustment of front wheel alignment. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1290 2014 Toyota RAV4 indicates Steering Angle Sensor Zero Point Malfunction.
- Common causes
- Common causes include Yaw rate and deceleration sensor zero point calibration incomplete, Poor adjustment of centered position of the steering wheel, Poor adjustment of front wheel alignment.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1290 2014 Toyota RAV4 Description
If front wheel alignment or steering wheel position is adjusted without disconnecting the negative battery terminal, or if the yaw rate and acceleration sensor zero point is not acquired after the adjustments have been completed, the Skid Control ECU (Brake Actuator Assembly) detects the difference between the previous zero point and newly acquired zero point and outputs this Diagnostic Trouble Code (DTC) to indicate a poor adjustment.
The steering sensor zero point malfunction warning will be canceled by turning the ignition switch off.
What are the Possible Causes of the DTC C1290 2014 Toyota RAV4?
- Yaw rate and deceleration sensor zero point calibration incomplete
- Poor adjustment of centered position of the steering wheel
- Poor adjustment of front wheel alignment
How to Fix the DTC C1290 2014 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1290 2014 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1290 2014 Toyota RAV4 code?
Need more information on how to fix the C1290 2014 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1290 2014 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1290 2014 Toyota RAV4 Code
What does the OBDII code C1290 mean for a 2014 Toyota RAV4?
The C1290 code indicates a malfunction with the steering angle sensor's zero point, which affects the vehicle's stability control and steering response.
What symptoms might I experience with the C1290 code?
You may notice issues such as the traction control light or ABS light illuminating on the dashboard, erratic steering feel, or problems with the stability control system.
What could cause the C1290 code to trigger?
Common causes include a misaligned steering angle sensor, damaged wiring or connectors, or a faulty steering angle sensor itself.
How can I reset the C1290 code after repairs?
You can reset the C1290 code using an OBDII scanner to clear the fault codes, but ensure that the underlying issue is resolved first to prevent the code from reappearing.
Is it safe to drive my RAV4 with the C1290 code?
While you can drive the vehicle, it may affect your control, especially in slippery conditions, so it's recommended to have the issue diagnosed and repaired promptly.
Can I fix the C1290 code myself?
If you have experience with automotive repairs, you can check the steering angle sensor alignment and wiring. However, professional diagnostics may be necessary for accurate repairs.
What tools do I need to diagnose the C1290 code?
You will need an OBDII scanner to read and clear codes, and possibly a multimeter to check the sensor's electrical connections and functionality.
How much does it typically cost to repair the C1290 code?
Repair costs can vary widely depending on the diagnosis, but fixing or replacing the steering angle sensor can range from $100 to $400, including labor.
What should I do if the C1290 code keeps coming back?
If the code persists after repairs, it's advisable to have the vehicle inspected by a qualified mechanic to check for underlying issues or faults in the vehicle's electronic systems.
Discuss the causes and fixes for C1290 2014 Toyota RAV4 OBDII Code
Code C1290 2014 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
