C1243 2018 Toyota RAV4 Code - Acceleration Sensor Stuck Malfunction
Quick Answer
The Skid Control ECU (Brake Actuator Assembly) receives signals from the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) via the Controller Area Network (CAN) communication system. Common causes include Acceleration Sensor Calibration, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly), Airbag Sensor Assembly harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1243 2018 Toyota RAV4 indicates Acceleration Sensor Stuck Malfunction.
- Common causes
- Common causes include Acceleration Sensor Calibration, Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly), Airbag Sensor Assembly harness is open or shorted.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1243 2018 Toyota RAV4 Description
The Airbag Sensor Assembly has a built-in Yaw Rate Sensor and Acceleration Sensor and detects the vehicle's condition.
If there is trouble in the bus lines between the Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly) and the CAN communication system, the Diagnostic Trouble Code (DTC) U0124 (malfunction in CAN communication with the acceleration sensor) is output.
These DTCs are also output when calibration has not been completed.
What are the Possible Causes of the DTC C1243 2018 Toyota RAV4?
- Acceleration Sensor Calibration
- Faulty Yaw Rate Sensor and Acceleration Sensor (Airbag Sensor Assembly)
- Airbag Sensor Assembly harness is open or shorted
- Airbag Sensor Assembly circuit poor electrical connection
How to Fix the DTC C1243 2018 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1243 2018 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1243 2018 Toyota RAV4 code?
Need more information on how to fix the C1243 2018 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1243 2018 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1243 2018 Toyota RAV4 Code
1. What are the common symptoms of OBDII code C1243 in a 2018 Toyota RAV4?
- Common symptoms include the vehicle going into limp mode, reduced acceleration, and the traction control light being illuminated on the dashboard.
2. What does the OBDII code C1243 in a 2018 Toyota RAV4 indicate?
- The code C1243 indicates a malfunction related to the acceleration sensor being stuck in the vehicle's electronic control system.
3. What are the possible causes of the acceleration sensor stuck malfunction in a 2018 Toyota RAV4?
- Possible causes include a faulty acceleration sensor, wiring issues, sensor calibration problems, or issues with the vehicle's electronic control unit (ECU).
4. How can I diagnose the acceleration sensor stuck malfunction in my 2018 Toyota RAV4?
- Diagnosis involves using an OBDII scanner to retrieve the trouble code, inspecting the wiring and sensor connections, and performing a calibration check on the acceleration sensor.
5. Can I continue driving my 2018 Toyota RAV4 with the acceleration sensor stuck malfunction?
- It is not recommended to drive the vehicle with this issue as it can affect the car's performance and safety systems. It's best to address the problem promptly.
6. How can I reset the OBDII code C1243 in my 2018 Toyota RAV4?
- You can reset the code using an OBDII scanner by clearing the trouble codes after addressing the underlying issue causing the acceleration sensor malfunction.
7. Is it necessary to replace the acceleration sensor if OBDII code C1243 appears in my 2018 Toyota RAV4?
- In some cases, replacing the acceleration sensor may be necessary if it is found to be faulty or stuck. Proper diagnosis will determine if a replacement is needed.
8. Can a DIY enthusiast repair the acceleration sensor stuck malfunction in a 2018 Toyota RAV4?
- Depending on your skill level and access to tools, you may be able to address wiring issues or sensor calibration problems. However, more complex repairs may require professional intervention.
9. How much does it typically cost to repair the acceleration sensor stuck malfunction in a 2018 Toyota RAV4?
- Repair costs can vary based on the specific issue causing the malfunction. Costs may involve sensor replacement, wiring repairs, and labor, so it's best to get a professional estimate.
10. How long does it take to repair the acceleration sensor stuck malfunction in a 2018 Toyota RAV4?
- The repair time can vary depending on the exact cause of the malfunction and the extent of the repairs needed. Simple fixes may take a few hours, while more complex issues could take longer.
Discuss the causes and fixes for C1243 2018 Toyota RAV4 OBDII Code
Code C1243 2018 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
