C1011 Lincoln Code - Brake Pedal Feel Simulator Cut-Off Pressure Sensor Signal Incorrect After Event
Quick Answer
The brake pedal feel simulator cut-off solenoid valve and brake pedal feel simulator cut-off pressure sensor are located within the brake pedal feel simulator, which is attached to the brake pedal assembly. Common causes include Faulty Brake Pedal Assembly, Brake Pedal Assembly harness is open or shorted, Brake Pedal Assembly circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1011 Lincoln indicates Brake Pedal Feel Simulator Cut-Off Pressure Sensor Signal Incorrect After Event.
- Common causes
- Common causes include Faulty Brake Pedal Assembly, Brake Pedal Assembly harness is open or shorted, Brake Pedal Assembly circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1011 Lincoln Description
The ABS module will apply a Pulse Width Modulated (PWM) ground signal to the brake pedal feel simulator cut-off solenoid valve to increase the resistance felt when the driver applies the brake pedal.
The ABS module uses input from the brake pedal feel simulator cut-off valve pressure sensor to verify that the brake pedal feel simulator cut-off solenoid valve is functioning properly. If the ABS module detects a fault with a brake system component that would adversely affect brake-by-wire operation, the module will remove power from the brake pedal feel simulator cut-off valve solenoid, relieving simulator fluid pressure.
The ABS module provides the brake pedal feel simulator cut-off pressure sensor a 5-volt reference voltage. The brake pedal feel simulator provides a signal voltage proportional to the fluid pressure in the brake pedal feel simulator cut-off device to the ABS module. The ABS module provides a signal return for brake pedal feel simulator cut-off pressure sensor.
What are the Possible Causes of the DTC C1011 Lincoln?
- Faulty Brake Pedal Assembly
- Brake Pedal Assembly harness is open or shorted
- Brake Pedal Assembly circuit poor electrical connection
How to Fix the DTC C1011 Lincoln?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
C1011:1F - Brake Pedal Feel Simulator Cut-Off Pressure Sensor: Circuit Intermittent
C1011:67 - Brake Pedal Feel Simulator Cut-Off Pressure Sensor: Signal Incorrect After Event
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1011 Lincoln code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1011 Lincoln code?
Need more information on how to fix the C1011 Lincoln code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1011 Lincoln code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1011 Lincoln Code
What does the OBDII code C1011 mean on a Lincoln vehicle?
1. Code C1011 indicates an issue with the Brake Pedal Feel Simulator Cut-Off Pressure Sensor, where its signal is detected as incorrect after an event. 2.
What are the common symptoms of code C1011 in a Lincoln?
Common symptoms include an illuminated ABS warning light, reduced brake pedal responsiveness, and potential issues with brake system performance. 3.
What causes the C1011 code to appear?
The code can be triggered by a faulty pressure sensor, wiring/connectors issues, or a malfunction in the brake pedal feel simulator system. 4.
Can I continue driving with the C1011 code active?
While the vehicle may still be drivable, it is not recommended as brake performance could be compromised, increasing safety risks. 5.
How can I diagnose the C1011 code on a Lincoln?
Start by scanning for codes using an OBDII scanner, then inspect the brake pedal feel simulator pressure sensor, wiring, and connectors for damage or faults. 6.
What repairs are commonly required to fix code C1011?
Repairs may include replacing the brake pedal feel simulator pressure sensor, repairing or replacing damaged wiring, or recalibrating the brake system module. 7.
How much does it cost to fix the C1011 code on a Lincoln?
Repair costs vary but typically range from $150 to $400, depending on whether the sensor or wiring needs replacement. 8.
Can a weak battery cause the C1011 code to trigger?
A weak or failing battery can sometimes cause electrical issues that may trigger the code, so it’s worth checking the battery voltage. 9.
Does the C1011 code affect the ABS system?
Yes, this code can impact the ABS system’s performance, potentially reducing its ability to prevent wheel lockup during braking. 10.
Do I need to reset the OBDII system after repairing the C1011 issue?
Yes, after completing repairs, clear the code using an OBDII scanner to ensure the issue is resolved and the system is functioning properly.
Discuss the causes and fixes for C1011 Lincoln OBDII Code
Code C1011 Lincoln comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
