C0710:5A Code - Steering Position Signal Not Plausible
Quick Answer
The Steering Wheel Angle Sensor receives a 12 V reference voltage from the Electronic Brake Control Module (EBCM). Common causes include Steering Wheel Angle Sensor Centering (Calibration), Faulty Steering Wheel Angle Sensor, Steering Wheel Angle Sensor harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C0710:5A indicates Steering Position Signal Not Plausible.
- Common causes
- Common causes include Steering Wheel Angle Sensor Centering (Calibration), Faulty Steering Wheel Angle Sensor, Steering Wheel Angle Sensor harness is open or shorted.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C0710:5A Description
What are the Possible Causes of the DTC C0710:5A?
- Steering Wheel Angle Sensor Centering (Calibration)
- Faulty Steering Wheel Angle Sensor
- Steering Wheel Angle Sensor harness is open or shorted
- Steering Wheel Angle Sensor circuit poor electrical connection
- Faulty Electronic Brake Control Module (EBCM)
How to Fix the DTC C0710:5A?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
Centering of the steering angle sensor might be required after certain service procedures are performed. Some of these procedures are as follows: Wheel alignment, steering gear replacement, steering column replacement, Steering Wheel Angle Sensor replacement, collision or other physical damage, and Electronic Brake Control Module (EBCM) replacement.
C0710:09 Steering Position Signal Too Fast Transitions
C0710:0A Steering Position Signal Too Slow Transitions
C0710:11 Steering Position Signal High Input
C0710:18 Steering Position Signal Low Signal Amplitude
C0710:19 Steering Position Signal High Signal Amplitude
C0710:42 Steering Position Signal Calibration Not Programmed
C0710:4B Steering Position Signal Calibration Not Learned
C0710:5A Steering Position Signal Not Plausible
C0710:71 Steering Position Signal Invalid Data
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C0710:5A code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C0710:5A code?
Need more information on how to fix the C0710:5A code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C0710:5A code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C0710:5A Code
1. What does the OBDII code C0710:5A mean?
The C0710:5A code indicates that the steering position signal from the sensor is not plausible, meaning the signal is inconsistent or outside expected parameters.
2. What are common symptoms of the C0710:5A code?
Symptoms may include a malfunctioning or inoperative electronic stability control (ESC), a warning light on the dashboard, and potential issues with power steering performance.
3. What causes the C0710:5A code to be triggered?
Common causes include a faulty steering angle sensor, wiring issues such as damaged or corroded connections, or a malfunctioning control module.
4. Can I drive my car with the C0710:5A code active?
While the vehicle may be drivable, compromised stability control or steering functionality could pose a safety risk, so it’s advisable to address the issue promptly.
5. How do I diagnose the C0710:5A code?
Diagnosis involves scanning the vehicle with an OBDII tool, inspecting the steering angle sensor and related wiring, and verifying the plausibility of the steering position signal.
6. How is the C0710:5A code typically fixed?
Repairs may include replacing the steering angle sensor, repairing or replacing damaged wiring, or reprogramming or replacing the control module if necessary.
7. Can the C0710:5A code be caused by low battery voltage?
Yes, low or fluctuating battery voltage can cause the steering angle sensor to send implausible signals, potentially triggering this code.
8. Does the C0710:5A code require calibration after repairs?
Yes, after replacing or repairing the steering angle sensor, a recalibration process may be needed to ensure the sensor functions correctly.
9. How much does it cost to repair the C0710:5A code?
Repair costs vary but can range from $150 to $400, depending on whether the steering angle sensor or related components need replacement.
10. Can a wheel alignment issue trigger the C0710:5A code?
Yes, improper wheel alignment or suspension issues can interfere with the steering angle sensor’s readings, potentially causing this code.
Discuss the causes and fixes for C0710:5A OBDII Code
Code C0710:5A comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
