B374A:05 Buick Code - Air Flow Control Position Feedback Circuit Short To Battery Or Open
Quick Answer
Doors in the Heating, Ventilation, and Air Conditioning (HVAC) case assembly are used to control airflow. Common causes include Faulty Mode Actuator, Mode Actuator harness is open or shorted, Mode Actuator circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B374A:05 Buick indicates Air Flow Control Position Feedback Circuit Short To Battery Or Open.
- Common causes
- Common causes include Faulty Mode Actuator, Mode Actuator harness is open or shorted, Mode Actuator circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B374A:05 Buick Description
Each actuator used in the system is a 5-wire bi-directional electric motor that incorporates a feedback potentiometer. The five circuits are low reference, 5 V reference, actuator position signal, and two control circuits. The control circuits use either ground or 12 V value to coordinate the actuator movement. In order to move the actuator, the HVAC control module grounds one of the control circuits while providing the other with 12 V. The HVAC control module reverses the polarity of the control circuits to move the actuator in the opposite direction.
When the actuator shaft rotates, the potentiometer's sliding contact changes the door position signal between 0-5 V. The HVAC control module converts the voltage signal to counts. The total range of the counts is 0-1024, with an operating range between 20-1000. The actual operating range of an actuator is determined during calibration. During calibration, the actuator is moved through its full range of travel, and the module stores the minimum and maximum value. Based on the desired system operation, the module sets a commanded, or targeted, value for the actuators. The control circuits are operated to move the door to the required position, and the changing position signal is sent to the module. Once the actual position signal and the commanded value are the same, the module ceases operating the control circuits and the actuator (and door) remains in the desired position.
The Diagnostic Trouble Code (DTC) will be set when the HVAC control module detects the sensor signal out of range. The signal voltage is greater than 4.9 V for more than 50 ms.
What are the Possible Causes of the DTC B374A:05 Buick?
- Faulty Mode Actuator
- Mode Actuator harness is open or shorted
- Mode Actuator circuit poor electrical connection
- Faulty Heating, Ventilation, and Air Conditioning (HVAC) Control Module
How to Fix the DTC B374A:05 Buick?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B374A:05 Buick code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B374A:05 Buick code?
Need more information on how to fix the B374A:05 Buick code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B374A:05 Buick code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about B374A:05 Buick Code
1. What does OBDII code B374A:05 mean on a Buick?
It indicates an issue with the Air Flow Control Position Feedback Circuit, specifically a short to battery or an open circuit.
2. What are the common symptoms of code B374A:05 on a Buick?
Symptoms may include improper air flow from vents, difficulty changing vent modes, HVAC system malfunctions, or a check engine light.
3. What causes the B374A:05 code on a Buick?
Common causes include damaged wiring, a faulty air flow control actuator, a blown fuse, or a malfunction in the HVAC control module.
4. Can I drive my Buick with the B374A:05 code?
Yes, but you may experience reduced HVAC functionality, and it’s best to address the issue promptly to avoid further complications.
5. How do I diagnose the B374A:05 code on a Buick?
Start by inspecting the wiring and connectors for damage, check the fuses, and test the air flow control actuator for proper operation.
6. How is the B374A:05 code typically fixed?
Repairs may involve replacing damaged wiring, repairing or replacing the air flow control actuator, or addressing a faulty HVAC control module.
7. How much does it cost to repair a B374A:05 code on a Buick?
The cost varies depending on the issue but typically ranges from $100 to $500, including parts and labor.
8. Can a faulty air flow control actuator trigger the B374A:05 code?
Yes, a malfunctioning air flow control actuator is a common cause of this code.
9. Will clearing the B374A:05 code fix the problem?
Clearing the code will reset the system temporarily, but the underlying issue must be addressed to prevent the code from returning.
10. Can a dead battery cause the B374A:05 code?
It’s unlikely, but a low or inconsistent voltage could potentially contribute to circuit issues, so the battery should be checked as part of the diagnosis.
Discuss the causes and fixes for B374A:05 Buick OBDII Code
Code B374A:05 Buick comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
