B374A:02 Cadillac Code - Air Flow Control Position Feedback Circuit Short To Ground
Quick Answer
Doors in the Heating, Ventilation, and Air Conditioning (HVAC) case assembly are used to control airflow. Common causes include Faulty Mode Actuator, Mode Actuator harness is open or shorted, Mode Actuator circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B374A:02 Cadillac indicates Air Flow Control Position Feedback Circuit Short To Ground.
- Common causes
- Common causes include Faulty Mode Actuator, Mode Actuator harness is open or shorted, Mode Actuator circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B374A:02 Cadillac Description
Each actuator used in the system is a 5-wire bi-directional electric motor that incorporates a feedback potentiometer. The five circuits are low reference, 5 V reference, actuator position signal, and two control circuits. The control circuits use either ground or 12 V value to coordinate the actuator movement. In order to move the actuator, the HVAC control module grounds one of the control circuits while providing the other with 12 V. The HVAC control module reverses the polarity of the control circuits to move the actuator in the opposite direction.
When the actuator shaft rotates, the potentiometer's sliding contact changes the door position signal between 0-5 V. The HVAC control module converts the voltage signal to counts. The total range of the counts is 0-1024, with an operating range between 20-1000. The actual operating range of an actuator is determined during calibration. During calibration, the actuator is moved through its full range of travel, and the module stores the minimum and maximum value. Based on the desired system operation, the module sets a commanded, or targeted, value for the actuators. The control circuits are operated to move the door to the required position, and the changing position signal is sent to the module. Once the actual position signal and the commanded value are the same, the module ceases operating the control circuits and the actuator (and door) remains in the desired position.
The Diagnostic Trouble Code (DTC) will be set when the HVAC control module detects the sensor signal out of range. The signal voltage is greater than 4.9 V for more than 50 ms.
What are the Possible Causes of the DTC B374A:02 Cadillac?
- Faulty Mode Actuator
- Mode Actuator harness is open or shorted
- Mode Actuator circuit poor electrical connection
- Faulty Heating, Ventilation, and Air Conditioning (HVAC) Control Module
How to Fix the DTC B374A:02 Cadillac?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B374A:02 Cadillac code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B374A:02 Cadillac code?
Need more information on how to fix the B374A:02 Cadillac code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B374A:02 Cadillac code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about B374A:02 Cadillac Code
1. What does the OBDII code B374A:02 mean on a Cadillac?
The code B374A:02 indicates an issue with the Air Flow Control Position Feedback Circuit, specifically a short to ground.
2. What are the symptoms of the B374A:02 code on a Cadillac?
Symptoms may include irregular HVAC airflow, inability to adjust air direction, unusual noises from the HVAC system, or a malfunctioning climate control system.
3. What causes the B374A:02 code to appear on a Cadillac?
The code is typically caused by a shorted wire in the Air Flow Control Position Feedback Circuit, a faulty actuator, or a damaged HVAC module.
4. Can a blown fuse cause the B374A:02 code on my Cadillac?
Yes, a blown fuse related to the HVAC system can disrupt the circuit and trigger the B374A:02 code.
5. How do I fix the B374A:02 code on my Cadillac?
Inspect the wiring and connectors for damage or corrosion, replace the air flow control actuator if faulty, and check the HVAC module for proper operation.
6. Can I drive with the B374A:02 code active on my Cadillac?
Yes, you can drive with this code, but it may cause discomfort due to limited HVAC functionality and should be addressed promptly.
7. How much does it cost to repair the B374A:02 code on a Cadillac?
The cost can range from $150 to $500, depending on whether you need to repair wiring, replace the actuator, or address HVAC module issues.
8. Is the B374A:02 code a common issue on Cadillacs?
It's not exceedingly common, but it can occur in vehicles with aging HVAC systems or those exposed to electrical issues.
9. How do I diagnose the B374A:02 code on my Cadillac?
Use a scan tool to verify the code, then inspect the air flow control circuit for shorts to ground, damaged wiring, or a malfunctioning actuator.
10. Will clearing the code B374A:02 fix the problem on my Cadillac?
Clearing the code may turn off the warning temporarily, but the underlying issue must be resolved to prevent the code from returning.
Discuss the causes and fixes for B374A:02 Cadillac OBDII Code
Code B374A:02 Cadillac comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
