B2792 Ford Code - Cross Link Between Firing Loops
Quick Answer
The Restraints Control Module (RCM) monitors all deployable devices for a cross link fault between circuits. Common causes include Faulty Restraints Control Module (RCM), Restraints Control Module (RCM) harness is open or shorted, Restraints Control Module (RCM) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2792 Ford indicates Cross Link Between Firing Loops.
- Common causes
- Common causes include Faulty Restraints Control Module (RCM), Restraints Control Module (RCM) harness is open or shorted, Restraints Control Module (RCM) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B2792 Ford Description
What are the Possible Causes of the DTC B2792 Ford?
- Faulty Restraints Control Module (RCM)
- Restraints Control Module (RCM) harness is open or shorted
- Restraints Control Module (RCM) circuit poor electrical connection
How to Fix the DTC B2792 Ford?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B2792 Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B2792 Ford code?
Need more information on how to fix the B2792 Ford code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2792 Ford code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B2792 Ford Code
1. What does the OBDII code B2792 mean on a Ford vehicle?
B2792 indicates a "Cross Link Between Firing Loops," meaning there's an issue with the ignition system where signals between firing circuits are interfering or crossed.
2. What are the common symptoms of the B2792 code in a Ford?
Symptoms may include engine misfires, rough idling, reduced engine performance, and the Check Engine Light being illuminated.
3. What causes the B2792 code to appear?
The code can be caused by damaged or shorted wiring in the ignition system, faulty ignition coils, a defective PCM (Powertrain Control Module), or incorrect spark plug installation.
4. Can a bad ignition coil trigger the B2792 code?
Yes, a faulty ignition coil can cause cross-linking or interference between firing loops, triggering the B2792 code.
5. How is the B2792 code diagnosed in a Ford?
A technician will inspect the ignition system wiring, test the ignition coils, check for proper spark plug installation, and use a scan tool to analyze related data.
6. Can I drive my Ford with the B2792 code?
Driving with this code is not recommended, as it may lead to poor engine performance, increased fuel consumption, and potential damage to the engine or catalytic converter.
7. How do you repair the B2792 code in a Ford?
Repairs may include replacing damaged wiring, faulty ignition coils, or spark plugs, and in rare cases, reprogramming or replacing the PCM.
8. Can dirty spark plugs cause the B2792 code?
Yes, worn or dirty spark plugs can disrupt proper ignition system operation, potentially leading to cross-linking between firing loops.
9. Is the B2792 code specific to Ford vehicles?
While B2792 is a generic OBDII code, its definition and troubleshooting steps can vary slightly. In Ford vehicles, it specifically relates to cross-linking in the ignition system.
10. How much does it cost to fix the B2792 code in a Ford?
The repair cost depends on the specific issue. Replacing spark plugs or ignition coils may cost $150–$400, while PCM replacement can exceed $1,000. Diagnostic fees are typically $100–$150.
Discuss the causes and fixes for B2792 Ford OBDII Code
Code B2792 Ford comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
