AutoCodes – Jeep – B2767 Jeep

B2767 Jeep Code - Left Impact Pressure Sensor

Quick Answer

The left side impact pressure sensor is located in the first row door. Common causes include Faulty Left Impact Pressure Sensor, Left Impact Pressure Sensor harness is open or shorted, Left Impact Pressure Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B2767 Jeep indicates Left Impact Pressure Sensor.
Common causes: Common causes include Faulty Left Impact Pressure Sensor, Left Impact Pressure Sensor harness is open or shorted, Left Impact Pressure Sensor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 1,826

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jan 27, 2020

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B2767 Jeep Description

The left side impact pressure sensor is located in the first row door. The impact pressure sensor performs its own self test using power supplied by the Occupant Restraint Controller (ORC) then communicate this status back to the ORC with periodic updates. The repair of this fault condition involves verifying the integrity of the wiring between the ORC and the sensor. The ORC continuously communicates with the Left Side Impact Pressure Sensor over the sensor signal circuit. The sensor communication and on board diagnostics are powered by the ORC signal.
This code will set, if the ORC and the Left Side Impact Pressure Sensor do not establish and maintain valid data communications. The Diagnostic Trouble Code (DTC) will become Active after the fault has set for nine seconds. The DTC will go to Stored after the ORC to Left Side Impact Pressure Sensor communication has recovered for 4 seconds.

OBDII Code B2767 Jeep - Left Impact Pressure Sensor - AutoCodes.com — B2767 Jeep Code - Left Impact Pressure Sensor

What does this mean?

What are the Possible Causes of the DTC B2767 Jeep?

Faulty Left Impact Pressure Sensor
Left Impact Pressure Sensor harness is open or shorted
Left Impact Pressure Sensor circuit poor electrical connection
Faulty Occupant Restraint Controller (ORC)

How to Fix the DTC B2767 Jeep?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B2767 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B2767 Jeep code?

Need more information on how to fix the B2767 Jeep code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B2767 Jeep code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B2767 Jeep Code

1. What are the common symptoms of OBDII code B2767 in a Jeep related to the Left Impact Pressure Sensor?

The common symptoms include the airbag warning light illuminating on the dashboard and potential issues with the deployment of the airbags during a collision.

2. What are the possible causes of OBDII code B2767 related to the Left Impact Pressure Sensor in a Jeep?

Possible causes may include a faulty left impact pressure sensor, damaged wiring or connectors, or issues with the airbag control module.

3. How serious is OBDII code B2767 in a Jeep related to the Left Impact Pressure Sensor?

This code is considered serious as it indicates a potential problem with the airbag system, which is crucial for occupant safety in the event of a collision.

4. Can I continue driving my Jeep with OBDII code B2767 related to the Left Impact Pressure Sensor?

It is not recommended to drive the vehicle with this code present, as it may affect the proper functioning of the airbags in the event of an accident.

5. How can OBDII code B2767 related to the Left Impact Pressure Sensor in a Jeep be diagnosed?

Diagnosis typically involves using a scan tool to read the fault codes, followed by inspecting the left impact pressure sensor, wiring, and connectors for any visible damage or issues.

6. What are some repair tips for fixing OBDII code B2767 in a Jeep related to the Left Impact Pressure Sensor?

Repair tips may include replacing the faulty left impact pressure sensor, repairing or replacing damaged wiring or connectors, and resetting the airbag system after repairs are completed.

7. Can I reset OBDII code B2767 related to the Left Impact Pressure Sensor in a Jeep myself?

While you can attempt to clear the code using an OBDII scanner, it is important to address the underlying issue causing the code to prevent it from reoccurring.

8. Are there any recalls or technical service bulletins related to OBDII code B2767 in a Jeep?

It is recommended to check with the manufacturer or authorized Jeep service centers to inquire about any recalls or technical service bulletins related to this specific OBDII code.

9. How much does it typically cost to repair OBDII code B2767 related to the Left Impact Pressure Sensor in a Jeep?

The cost of repair can vary depending on the specific cause of the issue, but it may involve sensor replacement, wiring repairs, and labor costs, which can range from a few hundred to over a thousand dollars.

10. Is it necessary to visit a dealership or can an independent mechanic fix OBDII code B2767 in a Jeep related to the Left Impact Pressure Sensor?

While a dealership may have specialized knowledge and tools for Jeep vehicles, an experienced independent mechanic with knowledge of airbag systems should be able to diagnose and repair the issue effectively as well.