B2762 Chrysler Code - Left C-Pillar Impact Acceleration Sensor
Quick Answer
The left side impact sensor 2 is located in the C-pillar area. Common causes include Faulty Left C-Pillar Impact Acceleration Sensor, Left C-Pillar Impact Acceleration Sensor harness is open or shorted, Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2762 Chrysler indicates Left C-Pillar Impact Acceleration Sensor.
- Common causes
- Common causes include Faulty Left C-Pillar Impact Acceleration Sensor, Left C-Pillar Impact Acceleration Sensor harness is open or shorted, Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B2762 Chrysler Description
This code will set, if the ORC and the Left Side Impact Sensor 2 do not establish and maintain valid data communications.
What are the Possible Causes of the DTC B2762 Chrysler?
- Faulty Left C-Pillar Impact Acceleration Sensor
- Left C-Pillar Impact Acceleration Sensor harness is open or shorted
- Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection
- Faulty Occupant Restraint Controller (ORC)
How to Fix the DTC B2762 Chrysler?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B2762 Chrysler code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B2762 Chrysler code?
Need more information on how to fix the B2762 Chrysler code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2762 Chrysler code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B2762 Chrysler Code
1. What does the OBDII code B2762 mean on a Chrysler vehicle?
B2762 indicates an issue with the Left C-Pillar Impact Acceleration Sensor, which is part of the airbag system responsible for detecting side impacts.
2. What are the common symptoms of the B2762 code?
Symptoms may include the airbag warning light being illuminated, potential deactivation of the airbag system, or no noticeable changes during normal driving.
3. What causes the B2762 code to appear?
Common causes include a faulty Left C-Pillar Impact Acceleration Sensor, damaged wiring or connectors, or a malfunction in the airbag control module.
4. Is it safe to drive with the B2762 code active?
It may be safe to drive, but the airbag system could be compromised, increasing the risk of injury in the event of a collision.
5. How can I diagnose the B2762 code?
Diagnosis typically involves scanning for fault codes, inspecting the sensor and associated wiring for damage, and testing the sensor's electrical connections.
6. What is the function of the Left C-Pillar Impact Acceleration Sensor?
This sensor detects side impacts near the left rear of the vehicle and sends data to the airbag control module to deploy airbags if necessary.
7. How do I fix the B2762 code?
Repairs may include replacing the faulty sensor, repairing or replacing damaged wires or connectors, or reprogramming/updating the airbag control module.
8. Can the B2762 code be cleared without fixing the issue?
Clearing the code without addressing the root cause is not recommended, as it will likely reappear and could leave the airbag system non-functional.
9. How much does it cost to repair the B2762 code?
Repair costs can vary but typically range from $100 to $300, depending on whether the sensor, wiring, or airbag control module needs replacement.
10. Do I need to recalibrate anything after replacing the Left C-Pillar Impact Acceleration Sensor?
Yes, in many cases, recalibration of the airbag system or reprogramming of the airbag control module may be necessary after replacing the sensor.
Discuss the causes and fixes for B2762 Chrysler OBDII Code
Code B2762 Chrysler comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
