B255D Chrysler Code - Decklid Open Position Sensor Circuit Performance
Quick Answer
The Convertible Top is fairly typical of convertible tops. Common causes include Faulty Decklid Open Position Sensor, Decklid Open Position Sensor harness is open or shorted, Decklid Open Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B255D Chrysler indicates Decklid Open Position Sensor Circuit Performance.
- Common causes
- Common causes include Faulty Decklid Open Position Sensor, Decklid Open Position Sensor harness is open or shorted, Decklid Open Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B255D Chrysler Description
1. Performance - These are time out DTCs, meaning the system timed out waiting for the next switch in sequence to change state. When the PTCM does not get the state change in the expected amount of time, it assumes something may be wrong and stops any further top operation in that direction. Typically the pump will run for 10 second before it times out.
2. Circuit Low - These DTCs set for a circuit that stays active at all times, meaning the signal circuit to the specified switch is continuously grounded. This could relate to a short to ground on the signal circuit, a sticking switch, or even a mechanical issue not allowing the switch to become inactive.
3. Correlation - These DTCs specifically relate two switches in a subcomponent (deck lid, tonneau drive, header latch, etc.) of the convertible top system. Both of the specified switches will be active in one position of the subcomponent (extended, retracted, open, closed, etc.). The switch that will not change state while attempting to operate the convertible top system, is the most likely area for attention.
What are the Possible Causes of the DTC B255D Chrysler?
- Faulty Decklid Open Position Sensor
- Decklid Open Position Sensor harness is open or shorted
- Decklid Open Position Sensor circuit poor electrical connection
- Faulty Power Top Control Module (PTCM)
How to Fix the DTC B255D Chrysler?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B255D Chrysler code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B255D Chrysler code?
Need more information on how to fix the B255D Chrysler code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B255D Chrysler code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about B255D Chrysler Code
1. What does the OBDII code B255D mean on a Chrysler?
B255D indicates an issue with the Decklid Open Position Sensor Circuit Performance, meaning the sensor isn't functioning properly or its signal is out of range.
2. What are the symptoms of code B255D on a Chrysler?
Common symptoms include the trunk or decklid not opening or closing properly, a trunk warning light on the dashboard, or issues with the remote trunk release.
3. What causes code B255D on a Chrysler?
Possible causes include a faulty decklid position sensor, damaged wiring or connectors, corrosion at the sensor connection, or a malfunctioning body control module (BCM).
4. How do you diagnose the B255D code on a Chrysler?
Diagnosis involves scanning for codes with an OBDII scanner, inspecting the decklid position sensor and its wiring, and testing the sensor’s signal with a multimeter.
5. Can a faulty decklid position sensor trigger the B255D code?
Yes, if the decklid position sensor is defective or its readings are inconsistent, it can trigger the B255D code.
6. How do you fix the B255D code on a Chrysler?
Repairs may include replacing the decklid position sensor, repairing or replacing damaged wiring, cleaning corroded terminals, or reprogramming the body control module if necessary.
7. Is it safe to drive with the B255D code active?
Yes, but you may experience inconvenience with the decklid operation, such as difficulty opening or closing the trunk, which could cause further wear or damage if left unresolved.
8. How much does it cost to repair the B255D code on a Chrysler?
The cost varies depending on the specific issue, but replacing the decklid position sensor typically ranges from $150 to $300, including parts and labor.
9. Can I fix the B255D code myself?
If you’re comfortable with basic automotive repairs, you can inspect the wiring and replace the decklid position sensor yourself. However, advanced diagnostics might require professional help.
10. Will clearing the code with a scanner fix the B255D issue?
Clearing the code may temporarily turn off the warning, but the underlying issue must be addressed to prevent the code from returning.
Discuss the causes and fixes for B255D Chrysler OBDII Code
Code B255D Chrysler comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
