AutoCodes – Jeep – B2306 Jeep

B2306 Jeep Code - Front Washer Switch Stuck

Quick Answer

The Wiper/Washer Switch is integral to the Multifunction Switch. Common causes include Faulty Multifunction Switch, Multifunction Switch harness is open or shorted, Multifunction Switch circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B2306 Jeep indicates Front Washer Switch Stuck.
Common causes: Common causes include Faulty Multifunction Switch, Multifunction Switch harness is open or shorted, Multifunction Switch circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 789

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Oct 31, 2019

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B2306 Jeep Description

The Wiper/Washer Switch is integral to the Multifunction Switch. The Multifunction Switch is connected to the left side of the Clockspring/SAS. The Multifunction switch provides the primary controls for the front wiper/rear wiper/washer systems, turn signals and for headlamp high beam selection. The Multifunction Switch communicates with the Steering Angle Sensor (SAS) (integral to the Steering Column Control Module) via the LIN Bus. The SAS then converts this data to a CAN Bus signal and broadcasts the message to the corresponding module on the bus. The Diagnostic Trouble Code (DTC) sets when the Steering Column Control Module (SCCM) detects the Washer Switch is active for greater than 20 seconds.

OBDII Code B2306 Jeep - Front Washer Switch Stuck - AutoCodes.com — B2306 Jeep Code - Front Washer Switch Stuck

What does this mean?

What are the Possible Causes of the DTC B2306 Jeep?

Faulty Multifunction Switch
Multifunction Switch harness is open or shorted
Multifunction Switch circuit poor electrical connection

How to Fix the DTC B2306 Jeep?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B2306 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B2306 Jeep code?

Need more information on how to fix the B2306 Jeep code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B2306 Jeep code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B2306 Jeep Code

1. What does the OBDII code B2306 mean on a Jeep?

The B2306 code indicates that the front washer switch is stuck, meaning the vehicle's computer has detected an issue with the washer switch not returning to its default position.

2. What are common symptoms of the B2306 code on a Jeep?

Common symptoms include the windshield washer fluid spraying continuously or not activating at all, and possibly an illuminated check engine or warning light.

3. What causes the B2306 code to appear?

The code is usually caused by a faulty washer switch, a shorted or damaged wiring harness, or debris obstructing the switch mechanism.

4. Can a stuck front washer switch damage my Jeep?

While itâ€™s not immediately damaging, a stuck switch can drain the washer fluid reservoir, cause electrical issues, or lead to inconvenience during rainy or dirty conditions.

5. How do I diagnose the B2306 code on my Jeep?

Start by visually inspecting the washer switch and its wiring for damage or debris. Use a scan tool to confirm the code and check the switch's electrical circuit for proper operation.

6. How can I fix the B2306 code?

Repairs may include cleaning or replacing the washer switch, repairing damaged wires, or addressing any debris causing the switch to stick.

7. Can I drive with the B2306 code active on my Jeep?

Yes, but itâ€™s not recommended for long-term use, especially if washer fluid is spraying uncontrollably or unavailable when needed for visibility.

8. How much does it cost to fix the B2306 code on a Jeep?

The cost depends on the specific issue but typically ranges from $50 to $200 for parts and labor if the washer switch needs replacement.

9. Can I reset the B2306 code without repairs?

You can clear the code with an OBDII scanner, but it will likely return if the underlying issue is not resolved.

10. Is the B2306 code common on Jeep vehicles?

Itâ€™s not a very common code, but it can occur on older models or vehicles with frequent use of the washer system. Regular maintenance can help prevent it.