B2293 Ford Code - Restraint System Air Bag Fault
Quick Answer
The Restraints Control Module (RCM) continuously monitors all front air bag module circuits (loop) for an acceptable resistance range, unacceptable voltage and shorts to ground. Common causes include Faulty Driver Air Bag Module, Driver Air Bag Module harness is open or shorted, Driver Air Bag Module circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2293 Ford indicates Restraint System Air Bag Fault.
- Common causes
- Common causes include Faulty Driver Air Bag Module, Driver Air Bag Module harness is open or shorted, Driver Air Bag Module circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B2293 Ford Description
As the RCM continuously monitors all front air bag module circuits for resistance, it expects a normal resistance for the driver and passenger air bag modules loop 1 and 2, between 1.31 to 4.29 ohms.
If a loop resistance for the driver and/or passenger air bag loop 1 and/or 2 is between 0.9 and 1.31 or between 4.29 and 5 ohms, there exists a strong potential for an intermittent fault, a DTC may or may not set. The RCM will also set an on-demand DTC if the loop resistance is less than 0.9 ohm or greater than 5 ohms.
What are the Possible Causes of the DTC B2293 Ford?
- Faulty Driver Air Bag Module
- Driver Air Bag Module harness is open or shorted
- Driver Air Bag Module circuit poor electrical connection
- Faulty Clockspring
- Faulty Restraints Control Module (RCM)
How to Fix the DTC B2293 Ford?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B2293 Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B2293 Ford code?
Need more information on how to fix the B2293 Ford code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2293 Ford code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B2293 Ford Code
1. What are the common symptoms of OBDII code B2293 for a Ford vehicle?
- The common symptoms include the airbag warning light staying illuminated on the dashboard and a message indicating a "Restraint System Air Bag Fault."
2. What is the main cause of OBDII code B2293 in a Ford vehicle?
- The main cause of code B2293 is typically a fault in the driver's side airbag module or its circuit.
3. Can OBDII code B2293 be triggered by a loose connection or wiring issue?
- Yes, loose connections or wiring issues related to the driver's side airbag system can trigger code B2293.
4. How should I approach repairing OBDII code B2293 for a Ford vehicle?
- It is recommended to start by inspecting the connections and wiring related to the driver's side airbag system, and if no issues are found, consider replacing the airbag module.
5. Is it safe to drive with OBDII code B2293 present in a Ford vehicle?
- It is not advisable to drive with the airbag warning light on, as it indicates a potential issue with the airbag system's functionality.
6. Are there any DIY repair tips for addressing OBDII code B2293 in a Ford vehicle?
- DIY repair tips may include checking and securing connections, inspecting wiring for damage, and if comfortable, replacing the driver's side airbag module.
7. Can resetting the OBDII system clear code B2293 temporarily?
- Resetting the OBDII system may temporarily clear the code, but if the underlying issue is not addressed, the code is likely to reappear.
8. How can I prevent OBDII code B2293 from recurring in my Ford vehicle?
- Regularly inspecting and maintaining the airbag system components, such as connections and the airbag module, can help prevent the recurrence of code B2293.
9. Should I attempt to diagnose and repair OBDII code B2293 myself or seek professional help?
- If you have experience with automotive electrical systems, you may attempt basic checks and repairs. However, for more complex issues, it is recommended to seek professional help.
10. Is OBDII code B2293 specific to certain Ford models or is it common across the brand?
- OBDII code B2293, related to the Restraint System Air Bag Fault, is commonly found in various Ford models equipped with OBDII systems.
Discuss the causes and fixes for B2293 Ford OBDII Code
Code B2293 Ford comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
