B220A Jeep Code - Occupant Restraint Controller Internal 1
Quick Answer
When powered, the Occupant Restraint Controller (ORC) performs an internal self test. Common causes include Faulty Occupant Restraint Controller (ORC), Occupant Restraint Controller (ORC) harness is open or shorted, Occupant Restraint Controller (ORC) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B220A Jeep indicates Occupant Restraint Controller Internal 1.
- Common causes
- Common causes include Faulty Occupant Restraint Controller (ORC), Occupant Restraint Controller (ORC) harness is open or shorted, Occupant Restraint Controller (ORC) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B220A Jeep Description
When Monitored the ORC checks the status and validity of the internal operating hardware and software at power up during the initialization process, and continuing through the ignition cycle.
Set Condition this Diagnostic Trouble Code (DTC) sets when a fault is detected internal to ORC hardware and/or software. Once set, this DTC is latched for the entire power cycle. If the same failure is detected in two consecutive power cycles, this DTC is latched active indefinitely.
What are the Possible Causes of the DTC B220A Jeep?
- Faulty Occupant Restraint Controller (ORC)
- Occupant Restraint Controller (ORC) harness is open or shorted
- Occupant Restraint Controller (ORC) circuit poor electrical connection
How to Fix the DTC B220A Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B220A Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B220A Jeep code?
Need more information on how to fix the B220A Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B220A Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B220A Jeep Code
What does the OBDII code B220A mean for a Jeep?
The OBDII code B220A indicates a malfunction in the Occupant Restraint Controller (ORC), specifically an internal fault within the controller.
What are the common symptoms associated with the B220A code?
Common symptoms may include airbag warning light illumination, potential issues with seatbelt pretensioners, and problems with the vehicle's airbag system.
What could cause the B220A code to trigger?
Causes may include a faulty Occupant Restraint Controller, damaged wiring or connectors, or issues with the vehicle's airbag system.
Can I drive my Jeep if the B220A code is present?
It is not recommended to drive the vehicle with this code present, as it may indicate that the airbag system is not functioning properly, posing a safety risk in the event of an accident.
How can I diagnose the B220A code?
To diagnose the B220A code, use an OBDII scanner to retrieve the code, inspect the ORC and associated wiring for damage, and check for any related codes that may provide additional insight.
What are some common repair solutions for the B220A code?
Repair solutions may include replacing the Occupant Restraint Controller, repairing or replacing damaged wiring or connectors, and clearing the code after repairs to test if it reappears.
Is it necessary to reset the airbag system after fixing the B220A code?
Yes, after repairs are made, it is necessary to reset the airbag system using a diagnostic scanner to clear the fault codes and ensure proper functionality.
Can a weak battery cause the B220A code to appear?
Yes, a weak or failing battery can lead to low voltage conditions that may trigger various fault codes, including B220A. Checking the battery and charging system is a good first step.
How much does it typically cost to repair the B220A code?
Repair costs can vary widely depending on the specific issue but may range from $100 to $800 or more, especially if the Occupant Restraint Controller needs to be replaced.
Discuss the causes and fixes for B220A Jeep OBDII Code
Code B220A Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
