B2008 Ford Code - Wipers On Signal Circuit Short To Ground
Quick Answer
The Smart Junction Box (SJB) sends a voltage signal to the headlamp switch and the light sensor. Common causes include Faulty Wiper Motor, Wiper Motor harness is open or shorted, Wiper Motor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2008 Ford indicates Wipers On Signal Circuit Short To Ground.
- Common causes
- Common causes include Faulty Wiper Motor, Wiper Motor harness is open or shorted, Wiper Motor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B2008 Ford Description
When the headlamp switch is placed in the AUTOLAMPS ON position, the voltage signal is routed to ground. When the SJB detects the headlamp switch in the AUTOLAMPS ON position, the SJB monitors the light sensor input. The light sensor determines the amount of light based on the input received from the ambient lighting conditions. When the ambient level has reached a point (determined by the internal programming of the SJB ), the SJB provides voltage to the headlamps, parking and license plate lamps. The Diagnostic Trouble Code (DTC) sets when the SJB detects a short to ground from the wipers on input circuit.
What are the Possible Causes of the DTC B2008 Ford?
- Faulty Wiper Motor
- Wiper Motor harness is open or shorted
- Wiper Motor circuit poor electrical connection
- Faulty Headlamp Switch
- Faulty Smart Junction Box (SJB)
How to Fix the DTC B2008 Ford?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B2008 Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B2008 Ford code?
Need more information on how to fix the B2008 Ford code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2008 Ford code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about B2008 Ford Code
1. What does the OBDII code B2008 mean on a Ford vehicle?
The B2008 code indicates a "Wipers On Signal Circuit Short To Ground," meaning there is a short circuit in the wiper control circuit.
2. What are the common symptoms of code B2008 in a Ford?
Symptoms may include wipers operating when not commanded, wipers not responding to controls, or intermittent wiper operation issues.
3. What causes the B2008 code to appear?
Common causes include damaged wiring, a short to ground in the wiper circuit, a faulty wiper switch, or a malfunctioning Body Control Module (BCM).
4. Can I drive my Ford with the B2008 code active?
Yes, but it’s not recommended to delay repairs, as faulty wipers could cause visibility issues during bad weather.
5. How do I diagnose the B2008 code?
Start by inspecting the wiper circuit wiring for visible damage, testing the wiper switch functionality, and checking for shorts or open circuits using a multimeter.
6. Is a faulty wiper motor a possible cause of the B2008 code?
While less common, a faulty wiper motor could contribute to the issue if it creates an electrical short in the circuit.
7. How do I fix the B2008 code on a Ford?
Repairs may include replacing damaged wiring, repairing the wiper switch, or reprogramming or replacing the Body Control Module (BCM) if necessary.
8. Will clearing the B2008 code fix the problem?
Clearing the code may temporarily remove the warning, but the underlying issue must be addressed to prevent it from returning.
9. What tools are needed to troubleshoot the B2008 code?
You’ll need an OBDII scanner, a multimeter, and possibly wiring diagrams for your Ford model.
10. How much does it typically cost to repair the B2008 code?
Repair costs vary but can range from $50 for minor wiring repairs to $500 or more if major components like the BCM need replacement.
Discuss the causes and fixes for B2008 Ford OBDII Code
Code B2008 Ford comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
