B1CC2 Jeep Code - Deployment Notification Output Circuit High
Quick Answer
The OBDII code sets when the Multi-Purpose Module (Police And Taxi Interface Module (PTIM)) has detected the Front or Side Airbag Status Signal circuits above a calibrated value. Common causes include Faulty Front/Side Air Bag, Front/Side Air Bag harness is open or shorted, Front/Side Air Bag circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1CC2 Jeep indicates Deployment Notification Output Circuit High.
- Common causes
- Common causes include Faulty Front/Side Air Bag, Front/Side Air Bag harness is open or shorted, Front/Side Air Bag circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1CC2 Jeep Description
What are the Possible Causes of the DTC B1CC2 Jeep?
- Faulty Front/Side Air Bag
- Front/Side Air Bag harness is open or shorted
- Front/Side Air Bag circuit poor electrical connection
- Faulty Aftermarket Light/Siren Controller
- Faulty Multi-Purpose Module (Police And Taxi Interface Module (PTIM))
How to Fix the DTC B1CC2 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1CC2 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1CC2 Jeep code?
Need more information on how to fix the B1CC2 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1CC2 Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1CC2 Jeep Code
1. What does the OBDII code B1CC2 mean on a Jeep?
The code B1CC2 indicates a "Deployment Notification Output Circuit High," which refers to an issue in the airbag system's notification circuit.
2. What are common symptoms of the B1CC2 code in a Jeep?
Symptoms include an illuminated airbag warning light, possible malfunction of the airbag system, and stored trouble codes in the vehicle's computer.
3. What causes the B1CC2 code to appear?
Common causes include a short circuit, damaged wiring or connectors in the airbag notification circuit, or a faulty airbag control module.
4. Is it safe to drive a Jeep with the B1CC2 code?
No, it is not recommended to drive with this code active because it indicates a potential issue with the airbag system, which could compromise safety in a collision.
5. How can I diagnose the B1CC2 code on my Jeep?
Start by scanning the vehicle with an OBDII scanner, inspecting the airbag system’s wiring and connectors, and testing the deployment notification circuit for continuity and proper voltage.
6. Can a blown fuse cause the B1CC2 code?
Yes, a blown fuse in the airbag system can cause this code, as it may interrupt the deployment notification circuit.
7. How do I fix the B1CC2 code on a Jeep?
Repairs may involve replacing damaged wiring, repairing connectors, or replacing a faulty airbag control module. Always follow proper safety protocols when working with the airbag system.
8. How much does it cost to fix the B1CC2 code?
The repair cost depends on the root cause. Minor fixes, like repairing wiring, may cost under $100, while replacing the airbag control module could cost several hundred dollars.
9. Can I clear the B1CC2 code without fixing the problem?
Clearing the code without addressing the underlying issue will not resolve the problem, and the code is likely to return.
10. Do I need a professional to fix the B1CC2 code on my Jeep?
Due to the complexity and safety risks of the airbag system, it is highly recommended to have a certified mechanic diagnose and repair this issue.
Discuss the causes and fixes for B1CC2 Jeep OBDII Code
Code B1CC2 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
