B1CC1 Jeep Code - Deployment Notification Output Circuit Low
Quick Answer
The OBDII code sets when the Multi-Purpose Module (Police And Taxi Interface Module (PTIM)) has detected the Front or Side Airbag Status Signal circuits below a calibrated value. Common causes include Faulty Front/Side Air Bag, Front/Side Air Bag harness is open or shorted, Front/Side Air Bag circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1CC1 Jeep indicates Deployment Notification Output Circuit Low.
- Common causes
- Common causes include Faulty Front/Side Air Bag, Front/Side Air Bag harness is open or shorted, Front/Side Air Bag circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1CC1 Jeep Description
What are the Possible Causes of the DTC B1CC1 Jeep?
- Faulty Front/Side Air Bag
- Front/Side Air Bag harness is open or shorted
- Front/Side Air Bag circuit poor electrical connection
- Faulty Aftermarket Light/Siren Controller
- Faulty Multi-Purpose Module (Police And Taxi Interface Module (PTIM))
How to Fix the DTC B1CC1 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1CC1 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1CC1 Jeep code?
Need more information on how to fix the B1CC1 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1CC1 Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1CC1 Jeep Code
1. What are the common symptoms of OBDII code B1CC1 in a Jeep related to Deployment Notification Output Circuit Low?
- Common symptoms include the airbag warning light staying on, intermittent airbag system failure, and loss of communication with the airbag module.
2. What are the typical causes of the B1CC1 code in a Jeep?
- The code B1CC1 is often caused by a faulty airbag control module, damaged wiring harness, loose connections, or a blown fuse related to the airbag system.
3. How can I diagnose the B1CC1 code in my Jeep?
- To diagnose the B1CC1 code, you may need to perform a thorough inspection of the airbag system wiring, connectors, and components. Using a diagnostic scanner to read the trouble codes and pinpoint the exact issue is also recommended.
4. What are the repair options for fixing the Deployment Notification Output Circuit Low code in a Jeep?
- Repair options include checking and repairing damaged wiring, replacing the airbag control module if necessary, ensuring all connections are secure, and resetting the airbag system codes with a diagnostic tool after the repair.
5. Can I drive my Jeep with the B1CC1 code present?
- It is not recommended to drive your Jeep with the B1CC1 code present, as it indicates a potential issue with the airbag system, which is crucial for your safety in case of a collision.
6. How serious is the B1CC1 code in a Jeep?
- The B1CC1 code related to the Deployment Notification Output Circuit Low is a serious issue as it directly impacts the proper functioning of the airbag system, which is a critical safety feature in your vehicle.
7. Will resetting the trouble codes clear the B1CC1 code in my Jeep?
- Resetting the trouble codes may temporarily clear the B1CC1 code, but it is important to address the root cause of the problem to prevent it from reoccurring and ensure the airbag system is functioning correctly.
8. Is it safe to attempt DIY repairs for the B1CC1 code in a Jeep?
- While some DIY repairs like checking connections and fuses can be done, it is recommended to have a professional technician diagnose and repair the B1CC1 code to ensure the airbag system is properly fixed and safe to use.
9. How much does it typically cost to fix the B1CC1 code in a Jeep?
- The cost of fixing the B1CC1 code can vary depending on the root cause of the issue, but it may range from a few hundred to over a thousand dollars, including parts and labor.
10. Can the B1CC1 code be intermittent in a Jeep?
- Yes, the B1CC1 code can sometimes be intermittent, causing the airbag warning light to come on and off sporadically. It is important to address the issue promptly to ensure the airbag system's reliability.
Discuss the causes and fixes for B1CC1 Jeep OBDII Code
Code B1CC1 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
